Step 4: Slide the upright tube cover (I) down to conceal tube connection. Use Tool6mm Note: Be careful not to pinch the sensor wire connection during assembly. Assembly ASSEMBLY FOR BACK REST SUPPORT TUBE Attach the back rest support tube (P) to the seat support tube (P) and secure using 3 allen screws (N1) and 3 flat washers (N3). 5 ASSEMBLY FOR SEAT SUPPORT FRAME Attach the seat support tube (P1) to the seat slide assembly (A10) and secure it using 4 allen screws (N1). A2PN1J1N8J1-1A10RA3For C

Keys Fitness assures the very best in value, appearance, durability and biomechanics. This manual will guide you through the assembly process. If at any time you are having trouble with the assembly or use of this product, then please contact us at our Keys Fitness Helpline. We have trained service technicians on site to take care of you, our valued customer. REGISTRATION CARD To avoid unnecessary delays in warranty parts and to insure that a permanent record of your purchase is on file with our

4009 Distribution Drive Suite 250 Garland, Texas 75041 Tel. 214.340.8888 Tel. 800.683.1236 Fax. 214.340.1768 Keysfitness

Model Name : KF-T2.0 Serial Number :____________ Serial number can be found at the location specified above. 100050 08/27 Rev 4.0 2 TABLE OF CONTENTS Thank You Thank You for making this unit a part of your exercise program. Keys Fitness assures the very best in value, appearance, durability and biomechanics. This manual will guide you through the assembly process. If at any time you are having trouble with the assembly or use of this product, then please contact us at our Keys Fitness Help line.

Press SQUARE PLUG (55) into the top of the REAR UPRIGHT (3). ?] Press FOUR 2"SQUARE CAPS (53) onto the end of the BASE TUBES ( as shown) in drawing. G\ Attach FOOT PLATE (17) to MAIN BASE FRAME (1) and insert "L" PIN (76) into the hole of the FOOT PLATE (17) and MAIN BASE FRAME (1). Press 2" SQUARE PLUG (77) into the end of the MAIN BASE FRAME (I) (as shown) in drawing. UPRIGHT ASSEMBLY TOP FRAME ASSEMBLY Attach TOP FRAME (7) to FRONT UPRJGHT (5). using 2- 3/8" x 3" BOLTS 4- 3/8" WASHERS 2-

Make sure that the word “Programs” does not appear below the track. Track 5 1-Step Speed buttons. If the Start button or the Speed increase button is pressed, the walking belt will begin to move at 1 mph. As you exercise, change the speed of the walking belt as desired by pressing the Speed increase and decrease buttons. Each time a button is pressed, the speed setting will change in increments of 0.1 mph; if a button is held down, the speed setting will change in increments of 0.5 mph. Note: Af

Do not move the treadmill over an uneven surface. 3. Place one foot against one of the wheels, and carefully lower the treadmill until it is resting in the storage position. Handrail Deck Wheel Engaged Catch Latch Knob Frame HOW TO LOWER THE TREADMILL FOR USE 1. Hold the upper end of the treadmill with your left hand. Pull the latch knob to the left and hold it. Pivot the frame downward and then release the latch knob. 2. Hold the metal frame firmly with both hands, and lower it to the floor. CA

Make sure that the Press Front Leg is turned so that the indicated hole is on the side shown. 6. Attach the Press Seat Frame (7) to the Press Upright (2) with two 3/8” x 3 1/4” Bolts (62), two 3/8” Flat Washers (48), and two 3/8” Nylon Locknuts (50). Attach the Press Seat Frame (7) to the Press Front Leg (20) with two 3/8” x 3 1/4” Bolts (62), two 3/8” Flat Washers (48), and two 3/8” Nylon Locknuts (50). Do not tighten the Nylon Locknuts yet. 5 7 76 50 50 6 20 Hole 4 3 62 1 50 62 50 14 50 48 48

With the treadmill connected to your computer, you can also go to and access iFIT.com programs directly from our Web site. See for more information. To use the manual mode of the console, follow the steps beginning on page 13. To use a preset program, see page 16. To create and use a custom program, see pages 17 and 18. To use a pulse program, see page 19. To use an iFIT.com MP3, CD, or video program, see page 23. To use an iFIT.com program directly from our Web site, see page 25. To operate the

You will need the following for installation: Pulley (44) - Qty. 8 Cable (46) - Qty. 1 Nylon Locknut (104) - Qty. 8 Long Pulley Spacer (53) - Qty. 6 Longer Pulley Spacer (55) - Qty. 4 Short Pulley Spacer (54) - Qty. 2 Bolt (91) - Qty. 3 Bolt (92) - Qty. 1 Bolt (93) - Qty 1 Bolt (94) - Qty. 1 Bolt (95) - Qty. 1 Washer (102) - Qty. 18 Pulley Bracket w/ Shaft (21) - Qty. 1 Pulley Bracket Block (22) - Qty. 1 Pulley Bracket (23) - Qty. 1 Figure 12 Assembly 22 Step 13 Note: This step is only used if y