Please staple your receipt and/or write in the name and phone number of the retail store where you purchased your EVO home gym. Name: Phone Number: Receipt: Open the boxes You are now ready to open the boxes of your new equipment. Make sure to inventory all of the parts that are included in the boxes. Check the Parts List for a full count of the number of parts included for this product to be assembled properly. If you are missing any parts or have any assembly questions contact your local Smoot

This Warranty does not apply to any product shipped or handled outside of the United States. This Warranty does not apply if the product is used for rental or commercial use. Consequential and incidental damages are not recoverable under this Warranty. (Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you.) THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER EXPRESS WARRANTIES. ALL IMPLIED WARRANTIES, I

EVO FX2 MOTORIZED TREADMILL Visit us at: 10 ASSEMBLY STEP 1: Remove your treadmill from the carton and place it on the floor in an open area as shown in FIG1. Raise the Left Upright (14) and secure with Bolts (77 and 76) and Washers (73 and 89). Repeat this step for the Right Upright (13). DO NOT FULLY TIGHTEN AT THIS POINT. EVO FX2 MOTORIZED TREADMILL 11 EVO FX2 MOTORIZED TREADMILL 11 ASSEMBLY STEP 2: Attach the Left Handlebar (24) and Right Handlebar (23) using Bolt (77) and Washer (73). Attac

TOLL FREE CUSTOMER SERVICE NUMBER: 1.888.800.1167 SERIAL NUMBER (found on frame): EVO FX2M MOTORIZED TREADMILL 2 EVO FX2M MOTORIZED TREADMILL 2 PRECAUTIONS For future service or related questions: Please staple your receipt and/or write in the name and phone number of the retail store where you purchased your Smooth Fitness treadmill. Name: ______________________________ Phone Number: ___________________ Receipt: ______________________ Precautions: WARNING: To reduce the risk of burns, fire, ele

Make sure that all bolts and nuts are tightened when equipment is in use. Periodic maintenance is required on all exercise equipment to keep it in good condition. Before beginning How you begin your exercise program depends on your physical condition. If you have been inactive for several years, or are severely overweight, you must start slowly and increase your time gradually, a few minutes per week. Initially you may be able to exercise only for a few minutes in your target zone. However, your

FX20 MOTORIZED TREADMILL Visit us at: 15 ASSEMBLY STEP 6: Attach the Upright Base Cover – Left #2 (18) and Upright Base Cover – Left #1 (17) over the Left Upright (15). Secure using three Plastic Fixing Insert (72) and three M4 x 15mm Screw (70). Attach the Upright Base Cover – Right #2 (19) and Upright Base Cover – Right #1 (20) over the Right Upright (16). Secure using three Plastic Fixing Insert (72) and four M4 x 15mm Screw (70). FX20 MOTORIZED TREADMILL Visit us at: 16 FOLDING INSTRUCTIONS

The resistance will be changed automatically while exercising, according to the following profile. To increase or decrease the resistance while exercising, press the UP/DOWN button. To pause the program while exercising, press the STOP button. To resume exercising, press the START button. If the RESET button is pressed after pausing the program, the computer returns to Power on Status. To return to the program mode press and hold the ENTER button. Interval Profile: (One complete cycle lasts 16 m

MILLIMETERS 0 10 20 30 40 50 60 70 80 90 100 hardware 8 Screw M4 x 19mm (4 pieces) 55 Screw #8 x 19mm (4 pieces) 16 Screw M6 x 20mm (2 pieces) 17 Screw M8 x 15mm (4 pieces) 121 Screw M8 x 19mm (4 pieces) 40 Metal Cap (2 pieces) Allen Wrench (1 piece) Wrench (1 piece) Wrench (1 piece) Wrench (1 piece) 130 Screw M6 x 15mm (2 pieces) 46 Bolt M8 x 78mm (2 pieces) 4 Safety Key (1 piece) Step 1: Remove your EVO 1CD Treadmill from the carton and place it on the floor in an open area as shown in FIG-1.

START: Press START to begin your exercise. ENTER: Press ENTER to confirm the setting of program. MODE: Press MODE to switch the display to show the information as RPM/TIME/PULSE or SPEED/DISTANCE/CALORIES or WATTS/LEVEL/TENSION (RESISTANCE). RESISTANCE UP/DOWN: Press UP/DOWN buttons to adjust the resistance. SPEED: Displays current exercise speed by Km/h or MPH LEVEL: Displays the current level of intensity of your exercise program. CALORIES: Count up: this measures total calories burned during

You will be prompted to fully tighten all fasteners later. Place the Base Frame (1) on the floor. Cap the Base Frame (1) with the 2" X 3" Rect End Plug (42). Cap the Rear Stabilizer (2) with two 1-3/8” x 3” Rect End Caps (41). Attach the Rear Stabilizer (2) to the Base Frame (1) using two 1/2" x 3" Hex Head Bolts (62), six 1/2" Washers (74) and four 1/2" Nylon Nuts (76) as shown in FIG 1. Cap the Upright (3) with the 2" x 3" Rect End Plug (42). Attach the Bumper (45) to the horizontal tube on th