Évaluations - 2, GPA: 4.5 ( )

Fabricant : Invacare Taille : 606.46 kb Nom Fichier : Langue d'enseignement:

This device is intended to provide a grip surface to a bed occupant to position themselves. DO NOT use for restraint purposes. DO NOT use this device as a push handle for moving the bed. ALWAYS test to make sure that this device is properly and securely in place before using. Although this device is not rated to any specific weight limitation, this device may become deformed or broken if excessive side pressure is exerted on this device. Installing the IHRAILTS-DLX Positioning Device NOTE: For this procedure, refer to FIGURE 6 and FIGURE 7. 1. When installing the positioning device IHRAILTS - DLX on a bed used with an 80-inch mattress, the head board mounting brackets and mattress keepers MUST be adjusted. Refer to Changing the Head Board Mounting Position and Changing the Mounting Position of the Mattress Keepers on page 7. 2. Raise the mattress deck to which the positioning device will be attached. 3. Locate the proper mounting holes on the bed to install the positioning device (FIGURE 6). FIGURE 6 Mounting Holes for Mounting Bracket Head End Mounting Holes for Mounting Bracket 8th Mounting Hole 5th Mounting Hole 1st Mounting Hole 4. Position the mounting bracket on the mattress deck (FIGURE 7). 5. Secure the mounting bracket to the mattress deck with the two hex bolts and locknuts (FIGURE 7). 6. Install the positioning device into the mounting bracket by sliding the mounting pin of the bed rail through the pivot tube (FIGURE 7). 7. Secure positioning device in place with two retaining clips (FIGURE 7). NOTE: Ensure that the release lever is pointing towards the foot end of the bed. 8. Slide the nylon washer over the end of the mounting pins (FIGURE 7). 9. Snap retaining clips into grooves on the end of the mounting pins (FIGURE 7). 10. Head End Mounting Bracket Only - Position the crossmember between the two bed rails (FIGURE 7). NOTE: Repeat STEPS 3-9 to install the other positioning device on the opposite side. Part No 1143214 5 ICCI Bed Rails and Accessories ICCI Bed Rails and Accessories 6 Part No 1143214 FIGURE 7 Installing the IHRAILTS-DLX Positioning Device Using the IHRAILTS-DLX Positioning Device NOTE: For this procedure, refer to FIGURE 8. 1. Perform one of the following: • Raising - Pull up on the positioning device while rotating towards the head end of the bed until the positioning device locks into place. • Lowering - Pull up on the release lever and push down on the positioning device while rotating towards the foot end of the bed until the positioning device lowers into place. FIGURE 8 Using the IHRAILTS-DLX Positioning Device Changing the Head Board Mounting Position NOTE: For this procedure, refer to FIGURE 9. NOTE: When using bed rails 6815A, 6816A, 6803A or IHRAILTS - DLX in conjunction with an 80-inch mattress, the head board mounting brackets MUST be adjusted. 1. Remove the two mounting screws that secure head board mounting bracket to the bed frame. See Detail “A”. 2. Secure the head board mounting bracket to the bed frame as shown in Detail “B” using two mounting screws and locknuts. Securely tighten. NOTE: Ensure mounting brackets are perpendicular to the floor. 3. Repeat STEPS 1-2 to install remaining head board mounting brackets. Release Lever (Towards the foot end of the bed) Mounting Bracket Hex Bolt Locknut Attach Head End Crossmember Here Mattress Deck Pivot Tube IHRAILTS-DLX Positioning Device Washer Retaining Clip Mounting Pin IHRAILTS-DLX Positioning Device Mattress Deck Mounting Bracket Pivot Tube Washer Retaining Clip Crossmember Positioning Device Release Lever DETAIL “B” DETAIL “A” NOTE: Mounting position of head board mounting bracket for brac...

Téléchargez votre

Pour télécharger, entrez 2 chiffres :