Évaluations - 2, GPA: 3.5 ( )

Fabricant : Invacare Taille : 606.46 kb Nom Fichier : Langue d'enseignement:

Install a socket screw into the head end and foot end mounting pins and tighten securely. 5. Securely tighten the hex bolts and locknuts that secure the pivot brackets to the bed frame. 6. Repeat STEPS 3-6 for the opposite bed rail. Installing 6815A, 6816A and 6803A Bed Rails NOTE: For this procedure, refer to FIGURE 2. 1. When installing bed rails 6815A, 6816A or 6803A on a bed used with an 80-inch mattress, the head board mounting brackets MUST be adjusted. Refer to Changing the Head Board Mounting Position on page 6. 2. Raise the mattress deck to which the bed rail will be attached. 3. Locate the proper mounting holes on the bed to install the bed rails. Refer to Detail “B” of FIGURE 2. 4. Position the mounting bracket on the mattress deck. Refer to Detail “B” of FIGURE 2. 5. Secure the mounting bracket to the mattress deck with the two hex bolts and locknuts. 6. Install the bed rail to the mounting bracket by sliding the mounting pin of the bed rail through the pivot tube. NOTE: Ensure that the release lever is pointing towards the foot end of the bed. ICCI Bed Rails and Accessories 2 Part No 1143214 Release Lever Bed Rail Towards the foot end of the bed) Socket Screw Mounting Bracket Hex Bolt Locknut Mattress Deck Attach Head End Crossmember Here Mounting Pin Pivot Tube DETAIL “A” - SIDE VIEW OF BED RAIL Bed Rail Mattress Deck Mounting Pin Crossmember (Head End On ly) Mounting Bracket Pivot Tube Socket Screw Head End DETAIL “B” - MOUNTING HOLE Foot End LOCATION FOR MOUNTING BRACKETS Mounting Holes for Mounting Bracket 8th Mounting Hole 1st 1st Mounting Mounting Hole Hole 5th Mounting Holes FIGURE 2 Installing 6815A, 6816A and 6803A Bed Rails 7. Secure the bed rail to the mounting bracket with the two socket screws. 8. Head End Mounting Bracket Only - Position the crossmember between the two bed rails as shown in Detail “A” of FIGURE 2 on page 3. 9. Repeat STEPS 3-7 to install the other bed rail on the opposite side. Using the Epoxy Bed Rails Towards Foot End of Bed Rail NOTE: For this procedure, refer to FIGURE 3. 1. Perform one of the following: • Raising - Pull up on the bed rails while rotating towards the head end of the bed until the bed rail locks into place. • Lowering - Pull up on the release lever and push down on the bed rail while rotating towards the foot end of the bed until the bed rail lowers into place. Bed Bed Rail in Lowered Position Release Lever FIGURE 3 Using the Epoxy Bed Rails (Head End) Part No 1143214 3 ICCI Bed Rails and Accessories Installing/Using Nylasar Bed Rails NOTE: The hardware shown in FIGURE 4 on page 4 is already assembled to the bars and latch arms before shipment. It is not necessary to remove the hardware from the bolt or to remove the bolt from the bars or latch arms. Holding the bolt in place while removing the hex nuts will prevent the hardware from becoming disassembled. In case of disassembly, refer to FIGURE 4 on page 4 for the correct placement of the hardware. Installing the IH5748A Bed Rails NOTE: For this procedure, refer to FIGURE 4 on page 4. NOTE: Invacare recommends two people perform the following installation procedure. One person should hold the bed rail up against the bed and one person should attach the rail to the bed. 1. Position the bed rail on the bed frame with the release lever towards the foot end of the bed. 2. Loosen and remove the hex nut from the latch arm at the foot end of the bed (Detail “B”). 3. Carefully push the bolt through the mounting hole in the bed frame (Detail “B”). 4. Loosely install the hex nut on the bolt to secure the latch arm to the bed frame (Detail “B”). 5. Loosen and remove the hex nut fro...

Téléchargez votre

Pour télécharger, entrez 2 chiffres :