Évaluations - 0, GPA: 0
(
)
)
|
Par ce dispositif a également d'autres instructions :
Facilité d'utilisation
About this document
Figure 2: Library (back view)
6. Secure the cluster and cable clamp to the library frame using
four Phillips screws (see Figure 4).
Installation
This document provides instructions for adding a tape drive
Figure 4: Installing the drive cluster
cluster to an HP StorageWorks ESL E-Series tape library.
Instructions
Before you begin
hp StorageWorks
Caution: Before continuing with the installation procedure,
ensure the library is powered off and that the main switches
Back access door
on the power distribution unit are turned off (to the left).
ESL E-Series Tape
Library Cluster Upgrade
Caution: Parts can be damaged by electrostatic discharge.
Keep parts in their containers until needed. Ensure you are
properly grounded when touching static-sensitive
7. Repeat step 2 through step 6 for each additional drive cluster
components.
to be installed.
Connecting drive cluster cables
Installing the drive cluster
Note: Drive clusters must be installed sequentially from top to bottom
(clusters 0 through 5). There can be no gaps between drive clusters.
1. Connect a power cable from the front of the power
Read instructions completely before
The library may contain up to 24 tape drives in 6 drive clusters
distribution unit, located on the lower left side of the library,
(see Figure 1).
to the drive cluster power connector below the power supplies
beginning the installation procedure
by routing it through the left cable access channel (see
Figure 1: Drive cluster numbering
2. Before continuing with the installation procedure, ensure the
Figure 5).
library is powered off and that the main switches on the
power distribution unit are in the off (left) position.
Figure 5: Connecting the cluster power cable
2
1
LNK
CHANNEL
LNK
CHANNEL
SERIAL
/
T
AC
FIBRE
/
T
AC
FIBRE
PWR
THERNET
E
T 0
OR
P
T 1
POR
LNK
CHANNEL
LNK
CHANNEL
SERIAL
/
T
AC
FIBRE
/
T
AC
FIBRE
PWR
THERNET
E
T 0
OR
P
T 1
POR
LNK
CHANNEL
LNK
CHANNEL
SERIAL
/
T
AC
FIBRE
/
T
AC
FIBRE
PWR
3. Using a 11/32-inch nut driver, remove the four nuts securing
THERNET
E
T 0
OR
P
T 1
POR
LNK
CHANNEL
LNK
CHANNEL
SERIAL
/
T
AC
FIBRE
/
T
AC
FIBRE
PWR
THERNET
E
T 0
OR
P
T 1
POR
LNK
CHANNEL
LNK
CHANNEL
SERIAL
/
T
AC
FIBRE
/
T
AC
FIBRE
PWR
THERNET
E
T 0
OR
P
T 1
POR
LNK
CHANNEL
LNK
CHANNEL
SERIAL
/
T
AC
FIBRE
/
T
AC
FIBRE
PWR
the cluster bin panel to the library (see Figure 3).
THERNET
E
T 0
OR
P
T 1
POR
4
3
Figure 3: Removing a cluster bin panel
Cluster 0
Cluster 1
Cluster bin panel
© Copyright 2004 Hewlett-Packard Development Company, L.P.
Hewlet -Packard Company makes no warranty of any kind with regard to
Cluster 2
this material, including, but not limited to, the implied warranties of
merchantability and fitness for a particular purpose. Hewlet -Packard shall
not be liable for errors contained herein or for incidental or consequential
Cluster 3
damages in connection with the furnishing, performance, or use of this
material.
This document contains proprietary information, which is protected by
Cluster 4
Nuts
copyright. No part of this document may be photocopied, reproduced,
or translated into another language without the prior written consent of
Hewlet -Packard. The information contained in this document is subject to
Cluster 5
change without notice.
Note: Retain the cable clamp and ensure it remains attached to the
Product names mentioned herein may be trademarks of their respective
drive cluster (see Figure 4). The clamp will be used for routing SCSI
companies as reflected by an associated footnote.
cables.
Hewlet -Packard Company shall not be liable for technical or editorial
errors or omissions contained herein. The information is provided “as is”
1. Make sure the back door of the library is open to access the
without warranty of any kind and is subject to change without notice. The
4. Align the drive cluster with the cabinet supports and insert it
warranties for Hewlet -Packard Company products are set forth in the
drive cluster bays (see Figure 2).
into the library.
express limited warranty statements for such products. Nothing herein
should be construed as constituting an additional warranty.
5. Add the cable clamp on top of the lower right screw hole on
Printed in the U.S.A.
the cluster.
2. Connect the I2C communications cable located to the right of
ESL E-Series Tape Library Cluster Upgrade Installation
each drive cluster to the I2C connector on the cluster
Instructions
controller (see Figure 6).
First Edition (January 2004)
Part Number: 355650-001
*355650-001*
See other side
... Ce manuel est également adapté pour les modèles :
données dispositifs de traitement - HP ESL 712e Ultrium Tape Library (769.77 kb)
données dispositifs de traitement - HP StorageWorks ESL 286e 286 Slot SDLT Library (769.77 kb)
données dispositifs de traitement - HP StorageWorks ESL 286e SDLT Tape Library (769.77 kb)
données dispositifs de traitement - HP StorageWorks ESL 322e 322 Slot Ultrium Library (769.77 kb)