Évaluations - 0, GPA: 0
(
)
)
|
Par ce dispositif a également d'autres instructions :
Facilité d'utilisation
15
16
ESL
hp
E-Series
StorageWorks
Mixed Media
Power on the library:
Installation
a. Verify that power cables are firmly in place.
b. Press the power button located behind the
laptop tray.
c. After several minutes, verify that the current
state of the library appears in the System
Caution: Parts can be damaged by
Note: These parts are not hot-
State display on the OCP (System On-line
electrostatic discharge. Keep parts in their
swappable. It is necessary to power
or System Off-line).
containers until needed. Ensure you are
down the library to replace these parts.
properly grounded when touching static-
Flip the two breaker switches on at the power
sensitive components.
Note: Be prepared to upgrade the
distribution unit.
corresponding drives, interface controllers,
Caution: To operate your library
and other hardware to the same technology
with mixed media, the library must have:
as the new panels. These must be
- Firmware version 2.0 or higher
purchased separately, and installed
- Removable load port magazines
following the instructions provided with
- Secure Manager for ESL with partitioning
the hardware.
17
18
enabled and one media type per
partition.
On the OCP, verify that the mixed media is
Note: This installation is most easily
installed and recognized:
performed by two people.
a. On the system status screen, the library
model number identifies the new panel type.
b. On the system status screen, the number of
slots identifies the new slot count.
c. Select the Menu button, then use the
Down button to highlight Cabinet and
press Select. If necessary, select the Down
1
2
ESL
E-Series
button to show the table at the bottom of the
hp
Mixed Media
Installation
StorageWorks
10348
Note: These parts are not hot-
y
swappable. It is necessary to power
screen. It will provide the number of slots,
down the library to replace these parts.
Caution: Parts can be damaged b
Note: Be prepared to upgrade the
electrostatic discharge. Keep parts in their
containers until needed. Ensure you are
corresponding drives, interface controllers,
properly grounded when touching static-
and other hardware to the same technology
sensitive components.
as the new panels. These must be
purchased separately, and installed
drives, and ports for SDLT, LTO, and the
Caution: Upgrade the library firmware
f
ollowing the instructions provided with
t
o version 2.0 or later before you perform
a upgrade procedure. In
the hardware.
the mixed medi
l
addition, to operate your library with mixed
Note: This installation is most easily
media, you must upgrade to removable load
performed by two people.
port magazines on the right, middle pane
library total.
(panel 5) of the library either before or
a upgrade.
during this mixed-medi
Close the back door of the library.
2
1
A
E
S
L
E-Series
e
2
400-FC 2G
I
n
t
e
rface
C
o
ntrol er
h
p
U
p
grade
S
t
o
rageWorks
2
1
1
A
es
Ensure the library feet are lowered to the floor,
so that the library is securely in place. To do
this, rotate each foot of the library until it mak
D
contact with the floor, then rotate each foot an
additional 1/4 turn.
B
E
3 Power off the library.
a. Use your backup software to verify that
the picker is empty, or to empty the picker.
laptop tray
C
b. Press the power button located on the
front of the library behind the
kit.
and wait until the OCP goes blank.
D. Installati
I
ns
E. Remova
A. Panel 1
packs
B. Panel 2
C. Panel 3
Getting help
D
Ensure the library feet are lowered to the floor
B
so that the library is securely in place. To do
• HP product information:
© 2004 Hewlett-Packard Development Company, L.P.
this, rotate each foot of the library until it makes
http://www.hp.com/support/else
contact with the floor, then rotate each foot an
First Edition (November 2004)
E
• HP technical support and phone numbers:
additional 1/4 turn.
Part Number: 373824-001
http://www.hp.com/support
• HP StorageWorks Library and Tape Tools
C
(L&TT) diagnostic software:
http://www.hp.com/support/tapetools
3 Power off the library.
a. Use your backup software to verify that
*373824-001*
• Interface Manager and HP StorageWorks
Inspect the contents of the kit.
the picker is empty or to empty the picker.
Command View ESL:
373824-001
A. Panel 1
D. Installation poster
b. Press the power button located on the
http://www.hp.com/support/cvesl
B. Panel 2
E. Removable magazines
front of the library behind the laptop tray
C. Panel 3
and wait until the OCP goes blank.
... Ce manuel est également adapté pour les modèles :
données dispositifs de traitement - HP ESL 712e Ultrium Tape Library (888.79 kb)
données dispositifs de traitement - HP StorageWorks ESL 286e 286 Slot SDLT Library (888.79 kb)
données dispositifs de traitement - HP StorageWorks ESL 286e SDLT Tape Library (888.79 kb)
données dispositifs de traitement - HP StorageWorks ESL 322e 322 Slot Ultrium Library (888.79 kb)