Évaluations - 2, GPA: 3.5
(
)
)
|
Facilité d'utilisation
This will stop and does not indicate a defect or hazard. • To clean steam vents before first use, prepare iron for steam ironing, then iron over an old cloth for a few minutes while letting the iron steam. Press the Blast button several times to clean the vents. Then follow the Self-Cleaning instructions. • Many irons spit or sputter during the first few uses with tap water. This happens as the steam chamber becomes conditioned. This will stop after a few uses. 3 1. Spray/Blast Buttons (see inset) 3. Water Tank Opening 4. Spray Nozzle 5. Water Window 6. Temperature Control Dial 7. Soleplate 8. Power On Light or Automatic Shutoff Reset Button/Light 9. Heel Rest 10. Cord 10:31 AM Page 4 840131800 ENv01.qxd 10/22/04 Using Your Iron To Dry Iron 1. Plug iron into outlet. 2. Turn Adjustable Steam Switch to Dry Iron . To Steam Iron 3. Turn Temperature Control Dial to desired temperature. Allow two minutes for iron to reach desired temperature. 4. To turn iron OFF ( O ), turn Temperature Control Dial to OFF ( O) and unplug iron. 1. Unplug iron. Turn Adjustable Steam Switch to Dry Iron . Set iron upright on heel rest. 2. Using a cup, slowly pour tap water into water tank opening until MAX fill line has been reached. Do not fill iron directly from the faucet. 3. Plug iron into outlet. 4. Turn the Temperature Control Dial to desired fabric setting in the steam range. 5. Allow two minutes for the iron to reach desired temperature. 6. Set Adjustable Steam Switch to the recommended steam level. See the “Fabric Setting Chart.” 7. To turn iron off, set Adjustable Steam Switch to Dry Iron . Turn the Temperature Control Dial to OFF ( O ). Unplug iron. 8. Empty water from the iron following directions in “Caring for Your Iron.” Water Please use ordinary tap water. If you have extremely hard water, alternate between tap water and distilled water for use in the iron. 4 840131800 ENv01.qxd 10/22/04 10:31 AM Page 5 Fabric Setting Chart Steam Setting Temperature Setting Ironing Instructions Dry IronOff Nylon, Acrylic Silk Polyester • • •• Dry iron using spray if necessary. Dry iron on the wrong side of the fabric. Iron while fabric is still damp. Steam Range Wool Rayon Cotton, Linen •• ••• ••• Use a press cloth and steam iron on the wrong side of fabric. Iron using spray if necessary. For cotton, iron while still damp or use spray. For linen, iron fabric on wrong side. Caring for Your Iron Iron 1. The water tank of your iron should be emptied after each use. Turn Temperature Control Dial to OFF ( O ). Unplug the iron and hold over a sink. Slowly tilt pointed end of iron down over sink. Water will run out of water tank opening. 2. After iron has completely cooled, wrap cord loosely around the iron and store in an upright position. Do not store iron laying flat on soleplate. Soleplate 1. Never iron over zippers, pins, metal rivets, or snaps, as these may scratch the soleplate. 2. To clean occasional build-up on the soleplate, wipe with a sudsy cloth. Do not use abrasive cleansers or metal scouring pads. 3. Always store iron upright in the heel rest position. Self-Clean To keep the steam vents clear of any build-up, follow these instructions each time you iron using steam. 1. Turn Temperature Control Dial to OFF ( O ) and set Adjustable Steam Switch to Dry Iron . Fill iron with water to 1.2 of its maximum capacity. 2. Turn Temperature Control Dial to Linen setting and let iron heat for 2 minutes. Keep Adjustable Steam Switch on Dry Iron . 3. Turn Temperature Control Dial to OFF ( O). Unplug iron and hold over a sink with soleplate facing down. 4. Turn Adjustable Steam Switch to MAX, while pressing Blast of Steam button often. Boiling water and steam will flow out of steam vents. Allow all water to drain from iron. 5. Gently move iron front to back to allow water to clean entire soleplate area. 6. If water still remains inside of sole- plate, reheat iron as indicated in Step 2. Boiling water and steam could still flow out of steam vents. 5 840131800 ENv01.qxd 10/22/04 10:32 AM Page 6 Optional Features (on selected models) Adjustable Steam Switch This knob provides steam for fabrics such as wool and linen. See the “Fabric Setting Chart” for details. Set the switch to Dry Iron to iron without steam. Spray and Blast of Steam Buttons Push Blast Button for an extra blast of steam. Push Spray Button to release a fine spray of water for difficult wrinkles in cotton or linen. Auto Shutoff Reset Button/Light This light comes on when the iron is first plugged in. After one hour, the iron will shut off and the light will go out. Push the Reset Button/ Light to turn the iron back on. Power On Light On units not provided with Auto Shutoff, this light comes on when the iron is plugged in and remains on until the iron is unplugged. The light stays on even if Temperature Control Dial is turned to OFF ( O). Retractable Cord 1. Pull cord to desired length. Do not unwind cord beyond colored tape indicator on cord. 2. To store cord, press and hold the Co...
Ce manuel est également adapté pour les modèles :Fers - 17610 (282.93 kb)