Évaluations - 1, GPA: 4
(
)
)
|
Facilité d'utilisation
This appliance is not intended for safety use by persons (including children) Never unscrew the boiler cap whilst the unit is pressurised. Steam will shoot out and burn you. . Don’t get burnt by the iron’s steam, hot water, soleplate or iron rest. . Keep children away from the steam station. And make sure they can’t grab the cords and pull the steam station down. . Trailing cords are a hazard, keep them out of the way to prevent accidents. . Never iron clothes being worn. . Never put the steam station, cord or plug in liquid – you could get an electric shock. . Always switch off and unplug the steam station before removing the boiler cap and filling with water. . Don’t let the power and steam supply cords touch hot parts. . During ironing pauses and after use always place the iron flat on the iron rest of the steam station. . Never leave the steam station on unattended. . Never use a damaged steam station. Get it checked or repaired: see ‘service and customer care’. . Do not use the steam station if it has been dropped, or if there are any visible signs of danger or it is leaking. . Don’t touch the appliance with wet or damp hands. . Always unplug the steam station when not in use and allow to cool before moving or cleaning. . It is extremely dangerous to direct the steam towards people or animals. . Only use water with this appliance. . During use, the steam station must be stable and used in a horizontal position. with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. . Children should be supervised to ensure that they do not play with the appliance. . Only use the appliance for its intended domestic use. Kenwood will not accept any liability if the appliance is subject to improper use, or failure to comply with these instructions. before plugging in Make sure your electricity supply is the same as the one shown on the underside of the steam station. . This iron complies with European Economic Community Directive 89/336/EEC. before using for the first time 1 Remove all packaging and any stickers or labels. 2Wind excess cord around the base of the steam station. 3Test the iron on an old cloth to make sure the soleplate and boiler are clean. We recommend that you allow steam to disperse by pressing the steam button in order to release any residues that may have built up during the manufacturing process. . Repeat step 3 after prolonged periods of storage. 2 know your Kenwood steam station . lock for continuous steam . steam button . temperature control with indicator light . soleplate . funnel . boiler cap . cord cactus locations . steam supply cord . cord storage . variable steam control . low water indicator light . on/off button . ready to steam indicator light . iron rest . power supply cord . cord cactus using your steam station 1 Place the steam station on the support of the ironing board or any other stable surface nearby with the iron sitting on the iron rest. Make sure the steam station is unplugged and that the power and steam supply cords are unrolled and not kinked. 2 Fit the cord cactus into one of the cord cactus locations. Place the steam supply cord into one of the grooves on the other end of the cord cactus. This will keep the cord in an upright position. filling with water 1 Unscrew the boiler cap by turning anticlockwise. 2 Use the funnel to fill the boiler. Maximum capacity when empty is 0.9 l. Take care not to overfill if the steam station contains water. 3 Refit the cap, don’t overtighten. . Filtered water is best as it reduces limescale, prolonging the life of your steam station (Kenwood water filters are widely available). Alternatively use 50% tap water and 50% distilled water. . Do not add anything else to the water such as water from clothes driers, scented water, water from refrigerators, air conditioners, batteries, bottled mineral water or rain water. These contain organic waste or mineral elements that become concentrated when heated and cause spitting, brown staining or premature wear to the steam station. refilling the boiler The red low water indicator light will glow when the boiler requires filling. NEVER UNSCREW THE BOILER CAP AS LONG AS THE BOILER IS UNDER PRESSURE. Carry out the following procedure to release the pressure: 1Press the steam button until the steam stops coming out - this may take several minutes, then release the steam button. 2Wait until the red low water indicator light comes on, then press the steam button again to release any residual steam. 3 Switch off and unplug the steam station and wait 5 minutes. 4 VERY SLOWLY unscrew the boiler cap. If any steam is heard, stop unscrewing the cap and wait until all the steam has gone. Once all the steam has gone continue to slowly unscrew the cap. 5 Use the funnel provided and slowly refill the boiler by pouring the water down the side of the funnel...
Ce manuel est également adapté pour les modèles :Fers - IC450 Series (386.28 kb)