manual-clean porcelain oven I Two oven racks I Two 8" @ 2,600W and two 6" @ 1,500W coil elements with porcelain drip pans Easy Set™ 105 electronic oven controls I Lift-up porcelain cooktop Selection White 22-45262 Oven Features Cleaning System Manual-Clean Oven Capacity (cu. ft.) 4.2 Electronic Oven Controls Easy Set" 105 Advanced Baking System Dual Radiant™ Variable Broiling System Hi/Lo Total Adjustable Oven Racks 2 Oven Light • Removable Glass Door • Window • Oven Interior WxH

In coastal areas, a slightly orange flame is unavoidable due to salt air. 14 PROTECTION AGREEMENTS Master Protection Agreements Congratulations on making a smart purchase. Your new Kenmordeproduct is designed and manufactured for years of dependable operation. But like all products, it may require preventive maintenance or repair from time to time. That's when having a Master Protection Agreement can save you money and aggravation. The Master Protection Agreement also helps extend the life of yo

2. Use a soap filled scouring pad with warm water or cover heavily soiled spots with a solution of clear water and ammonia. Scour gently. Rinse and wipe dry with a clean cloth. SURFACES CLEANING AGENTS INSTRUCTIONS Porcelain enamel Mild cleaners or soap-Use a damp sponge or damp( cooktop, surface filled steel wool pads. ened soap pad, rinse and dry. under cooktop) Broil Insert Hot, soapy water or Use a clean soapy, dampened Control Panel cleaner cream. cloth or paper towel, remove soil and dry.

DO NOT cook with the surface control knob in the LITE position. (The electronic ignitor will continue to spark if the knob is left in the LITE position.) Setting Proper Surface Burner Flame Size For most cooking, start on the highest control setting and then turn to a lower one to complete the process. Use the recommendations below as a guide for determining proper flame size for various types of cooking. The size and type of utensil used and the amount of food being cooked will influence the se

Proper Burner Head placement insures that each Burner will have the correct spark required for surface gas ignition. 2. Place the correct Burner Caps at each of the burner locations. Each of the Burner Heads MUST have a Burner Cap installed to insure proper ignition and gas flame size (See Figure 2). 3. Place the 2 (two) or 3 (three) cast iron Burner Grates supplied with the range. Carefully lift the burners grates on to the cooktop over the burners. Properly installed Burner Grates will rest wi

Improper flame size Figure 2 9 Setting Surface Controls Setting the Dual Burner (present on Models 790.3248 & 790.3249 only) The Dual Burner has two rings of flame that you can control for two different heat levels, one for small and one for large cookware. Small Cookware Operation (Figure 1 ; Zone A) 1. Place a small cooking utensil centered over the surface Burner Grate. 2. Push the surface control knob in and turn counterclockwise out of the OFF position (See Figures 2 & 3). 3. Release the kn

If the burner does not remain lit, increase the minimum gas rate setting. To adjust the minimum gas rate setting: Turn on the burner. Turn the tap to the MINIMUM position. Take off the knob. With a small flat screwdriver turn the screw to the correct regulation. Note: for LPG gas, the regulation screw is normally tightened up. Fig. 10 Adjusting the minimum burner setting Table for the choice of injectors Natural gas 1.0 LPG gas 2.75Test Point Pressure [kPa] BURNER Injector Orifice Dia. [mm] Gas

3101=:_" -,-= color number, nt_mero de color iii....... Sears Roebuck and Co., Hoffman Estates, IL 60179 U.S.A. P/N 318200678 Re_,;A (0603) www, sears,com Table of Contents Product Record Cooktop Warranty .............................................................. 2 In this space below, record the date of purchase, model and Product Record ................................................................. 2 serial number of your product. You will find the model and Serial Plate Location ......

Do not attempt to deep fat fry too much food at once as the food will neither brown nor cook properly. Setting Surface Controls (cont'd) Setting the Bridge Burner The Bridge Burner should be used with rectangular shaped cookware. Cookware like the cast-iron Griddle that is supplied with your cooktop is designed specifically for best results with the Bridge Burner. The Bridge Burner feature may be used to combine the cooking power of 2 or if needed 3 gas surface Burners located along the left-han

Be sure all controls are turned to OFF and burner grates Gas Valve are cool before removing cooktop burner units. Burner Orifice Support To Remove Burner Assemblies 1. Remove the shipping screw from the support brackets. See illustrations for location of screws. 2. Grasp the burner head and tilt it slightly (A in Figure 1) to the right to release the tab from the burner support. 3. Lift up the support bracket (see Figure 2) slightly and pull it away from the front of the cooktop to free the air