Évaluations - 4, GPA: 3.8
(
)
)
|
Facilité d'utilisation
2 hook recess Installation Three identical wall mounting brackets are stored in the polystyrene packaging of the heater. Please note that the radiator must only be wall mounted using the brackets supplied. Warning: This heater must not be located immediately below a fixed socket outlet. The plug must be accessible after heater installation. floor mounted wall mounted CVP1T shown IMPORTANT SAFETY ADVICE WARNING - THIS APPLIANCE MUST NOT BE USED IN A BATHROOM WARNING – DO NOT USE THIS HEATER IN THE IMMEDIATE SURROUNDINGS OF A BATH, A SHOWER OR A SWIMMING POOL WARNING – THIS HEATER MUST NOT BE LOCATED IMMEDIATELY BELOW A FIXED SOCKET OUTLET. DO NOT USE THE HEATER UNTIL THE FEET OR WALL BRACKETS ARE FITTED CORRECTLY. FOLLOW these instructions carefully. The heater carries a warning ‘DO NOT COVER’ to alert the user to the risk of fire that exists if the heater is accidentally covered. This appliance is not intended for use by children or other persons without assistance or supervision if their physical, sensory or mental capabilities prevent them from using it safely. Children should be supervised to ensure that they do not play with the appliance. We recommend a guard be fitted to ensure contact with the heater is avoided and objects cannot be inserted in to the product. If the mains lead is damaged, it must be replaced by the manufacturer or its service agent or a similarly qualified person in order to avoid a hazard. For further information, please contact our guard supplier direct on Tel. No. 01603 667957, or in case of difficulty or for further advice contact the Customer Helpline - (details on back page) Electrical WARNING – THIS APPLIANCE MUST BE EARTHED If the socket outlets in your home are not of the 13 amp BS1363 type they will not accept the plug connected to this heater, therefore cut off the plug. When cut off this plug can constitute a shock hazard if inserted into a socket outlet. It must therefore be disposed of safely. Before wiring the appropriate plug please note that the wires in this mains lead are coloured in accordance with the following code: GREEN/YELLOW - EARTH BLUE - NEUTRAL BROWN - LIVE Connect the Green/Yellow wire to the terminal marked E or the earth symbol or coloured Green or Green/Yellow. Connect the Brown wire to the terminal marked L or coloured Red. Connect the Blue wire to the terminal marked N or coloured Black. DO NOT connect the Brown (Live) or the Blue (Neutral) wires to the Earth terminal of your 13 amp plug. If the terminals of the plug are unmarked or you are in any doubt, consult a qualified electrician. CAUTION: If you use this heater in conjunction with a thermal control, programme controller, timer or any other device which switches the heater on automatically observe all safety warnings at all times. Positioning the Heater Select the position for the heater ensuring there is clearance from any furniture and fittings of at least 150mm above the heater, 230mm below (wall mounted) and 75mm each side - see Fig. 1. Curtains must not be closer than 150mm from the top of the heater. If used in a free-standing position the heater should be on a flat stable surface. Free Standing Operation NEVER USE THE HEATER FREE STANDING WITHOUT THE FEET FITTED. 1. Lay the heater on it’s front. 2. Locate and remove the two foot fixing screws using a X-head screwdriver. 3. Place the feet over the base of the heater, align holes and engage hook on foot into recess on the back of the heater - see Fig. 2. 4. Replace the screws but do not over tighten. 13 : 17 ON OFF ADVANCE AUTO MAN ON OFF P1 Follow the sequence outlined below when installing the heater. 1. Select the position for the heater ensuring there is clearance from any furniture and fittings of at least 150mm above the heater, 230mm below and 75mm each side. Curtains must not be closer than 150mm from the top of the heater. 2. Fig. 3 shows the required drill hole positions. Using a straight edge draw a horizontal line for the top brackets at the required mounting height from the floor. On this line mark off the fixing centres at 497mm. 3. Fix the two top retaining brackets to the wall, using suitable fixings. Ensure that suitable fixings are placed in both of the fixing holes provided in each bracket. 4. Locate the heater on the top brackets and allow it to hang in place. 5. Fit the bottom bracket into the slot in the heater and then let it rest against the wall. Mark the hole positions. 6. Remove the heater and drill and plug the holes for the bottom bracket. 7. Re-hang the heater with the bottom bracket fitted to the heater and screw fix the bracket to the wall. Test that the heater is now securely fixed to the wall. Note: We recommend that the heater should be wall mounted in rooms where children may be left unattended. See also ‘Important Safety Advice’. Operation Important – Objects or clothing must not be placed on this heater. Before using the heater ensure that all warnings and instructions have been read carefully. Fig. ...
Ce manuel est également adapté pour les modèles :Ventilateurs - CVP1T (306.97 kb)