Log:
Évaluations - 2, GPA: 5 ( )

Instructions AEG, Modèle DL 4150

Fabricant : AEG
Taille : 171.95 kb
Nom Fichier :
Langue d'enseignement: en
Aller à la télécharger



Facilité d'utilisation


Attention: the metal grease filters must be removed and washed, either by hand or in the dishwasher, every four weeks. Removing the metal grease filter DL 4150 - CHDL 4150 - DL 6250 • Press the handle that locks the grease filter first towards the opposite side and then extract downwards. Fig. 4. 570 D - 5708 D • Fold the handles downwards and press them towards the centre. Fig. 4. Grease filter Handle DL 4150 - CHDL 4150 DL 6250 Handle 570 D - 5708 D Fig. 4 Hand washing Soak grease filters for about one hour in hot water with a little washing up liquid added, then rinse off thoroughly with hot water. Repeat the process if necessary. Refit the grease filters when they are dry. Dishwasher Place grease filters in the dishwasher. Select most powerful washing programme and highest temperature, at least 65°C. Repeat the process. Refit the grease filters when they are dry. When washing the metal grease filter in the dishwasher a slight discolouration of the filter can occur, this does not have any impact on its performance. • Clean the inner housing using a hot detergent solution only (never use caustic detergents, abrasive powders or brushes). Charcoal filter • The charcoal filter should only be used if you want to use the hood in the recirculation function. • To do this you will need an original AEG charcoal filter (available from your local Service Force Centre). • The charcoal filter cannot be washed nor regenerated. The charcoal filter should be replaced every 12 months under normal use. Replacement filters are available from your local Service Force Centre. • Fitting Remove the grease filter. Fit the charcoal filter on the lamp side, press in both red lugs on the charcoal filter, and unclip the charcoal filter forwards (towards the front edge of the appliance). Refit the grease filter. • To remove proceed in the reverse order. • Always specify the hood model code number and serial number when ordering replacement filters. This information is shown on the registration plate located on the inside of the unit. • The charcoal filter can be ordered from your local AEG Service Force Centre. Fig. 5 Warning • Failure to observe the instructions on cleaning the unit and changing the filters will cause a fire hazard. You are therefore strongly recommended to follow these instructions. • The manufacturer declines all responsibility for any damage to the motor or any fire damage linked to inappropriate maintenance or failure to observe the above safety recommendations. Changing the light bulb • Disconnect the cooker hood from the main supply. • Unlock the lamp cover by twisting the bolts to the left and fold down the bulb cover. • Replace the old bulb with a new one of the same type. • Close the bulb cover and relock it by twisting the bolts to the right. • If the light does not come on, make sure the bulb has been inserted correctly before contacting your local Service Force Centre. Fig. 6 What to do if If your appliance fails to work properly please carry out the following checks. Symptom Solution The cooker hood will not start... Check that: The hood is connected to the electricity supply. Check that a fan speed has been selected The cooker hood is not working effectively.. Check that: The fan speed is set high enough for the task. The grease filters are clean. The kitchen is adequately vented to allow the entry of fresh air. If set up for recirculation, check that the charcoal filter is still effective. If set up for extraction, check that the ducting and outlets are not blocked. ...

Ce manuel est également adapté pour les modèles :
Ventilateurs - 570 D (171.95 kb)
Ventilateurs - CHDL 4150 (171.95 kb)
Ventilateurs - DL 6250 (171.95 kb)
Ventilateurs - 5708 D (171.95 kb)

Écrivez votre propre critique du dispositif



Texte du message
Votre nom :
Entrez les deux chiffres :
capcha





catégories