Évaluations - , GPA: ( )

Instructions Electrolux, Modèle 5708 D

Fabricant : Electrolux
Taille : 171.95 kb
Nom Fichier : 854c86f6-663c-4630-b3cf-1cb63d11ea8d.pdf

Langue d'enseignement:

Le document est chargé, s'il vous plaît patienter

Téléchargez votre Fermer

Le document est chargé, s'il vous plaît patienter

Téléchargez votre Fermer

Appliances fitted with a plug can be connected to any standard power socket within easy access. Should it be necessary to provide a fixed connection, the hood must only be installed by an electrician authorised by the local electricity board. When installing, an omnipolar disconnector with a distance of at least 3 mm between contacts must be provided. Fixed connection of the appliance must only be carried out by an authorised electrician. Electrical connection for UK only Safety warnings for the electrician Connect the hood to the mains supply via a double pole switch which has 3 mm minimum separation between the contacts. The switch must be accessible at all times. The following is valid in the United Kingdom only: -the wire which is coloured green and yellow must be connected to the terminal which is marked with the letter E or by the earth symbol ( ), or coloured green or green and yellow; -the wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black, - the wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured red. Installation - Fig. 8 • Drill the base of the wall unit to allow for passage of the hood body. Fig. 7. • Drill the top of the wall unit to allow for passage of the exhaust pipe and the electrical cable. Fig. 7. • Remove the grease filter (1). • Remove the grease filter support frame, by pressing the two spring clamps located at the sides of the frame (2). • Through the top of the wall unit, insert a pipe with a diameter of 120mm at the connection ring (3). • Fit the connection ring on the hood exhaust outlet (4) and fasten it to the exhaust pipe. • Insert the body of the hood into the hole in the base of the wall unit (5) – check the position of the exhaust pipe and the electrical cable, press firmly so that the anchor springs (6) engage above the bottom of wall unit. Tighten the screws in the anchor springs firmly. • If necessary the hood can be fastened with four more screws (7). • Replace the grease filter support frame. • Replace the grease filter. Fig. 8 Removing the hood from cabinet Follow these steps: • Remove the grease filter. • Remove the 4 additional screws from the frame. • Loosen the screws on the two fixing springs. Fig. 9. Fig. 9 • Push a flat screwdriver into the hole for the fixing springs (right and left) and push each of the fixing springs inwards. Fig. 10. • At the same time, pull the extractor hood (right and left) out of the cabinet. Re-install it as described above. Fig. 10 Relocating the control unit (Only 570 D - 5708 D) The control unit can be fitted at a different point (cladding, lighting facia, etc.). Remove the grease filter grill and the housing frame. 1. Loosen two screws and pull the control unit forwards out of the housing. Undo the socket connection. Caution: The socket connection cable is only long enough for a maximum distance of 40 cm! Fig. 11 2. Open the cable channel on the top side of the housing and pull the wire for the control unit through the opening. Shut the cover so that it supports the wire. 3. Fit the fascia cover included with the appliance over the opening for the control unit. 4. Dimensions to cut out for the control unit: Fig. 12 From the Electrolux Group. The world.s No.1 choice. The Electrolux Group is the world.s largest producer of powered appliances for kitchen, cleaning and outdoor use. More than 55 million Electrolux Group products (such as refrigerators, cookers, washing machines,va...