Log:
Évaluations - 3, GPA: 5 ( )

Instructions Dimplex, Modèle DXLWP800TI N

Fabricant : Dimplex
Taille : 200.08 kb
Nom Fichier :
Langue d'enseignement: en
Aller à la télécharger



Facilité d'utilisation


Models with Timer DXLWP400TI, DXLWP800TI N & ARLWP800TI Set the I - .......... - O slide switch on the timer (Fig. 3) to : Position O - Heating Off Position I - Manual operation This setting allows power to the heater uninterrupted by the timer settings. The heat selector switch will control the output (see ‘Using the heater’). Position .......... - ‘Auto’ operation DO NOT disconnect this heater from the mains supply unless it is being taken out of use (e.g. in summer or for storage), otherwise the timer clock will stop. Setting the time of day To set the time of day, rotate the timer dial clockwise (indicated by the arrow) until the correct time of day is opposite the reference mark (see Fig. 4). The 24-hour clock is used ; e.g. time shown for 3 pm is ‘15’ (15:00hrs). Setting the ‘Auto’ ON and OFF times To set the timer : 1. Using your finger tip or the tip of a pencil, push in as many segments as necessary around the dial, according to the times you don’t require heat – see Fig. 4. Each segment pushed in switches the heater OFF for that part of the hour. All other segments will be ON. For example, Fig. 5 shows the timer set to switch the heater ON between 7 am and 9 am and between 4 pm and 9.30 pm . 2. You can select as many ON periods as you like, within the 24-hour day. The settings will repeat every day until changed. 3. To change ON and OFF times, simply push in any ‘ON’ segments you wish to cancel and pull out new ‘ON’ segments as required. Switching to auto Set the heat selector and thermostat for the heat output required. Check that the clock shows the correct time of day. Set the I - .......... - O slide switch to .......... (see Fig. 4) - the convector will switch ON and OFF according to the timer settings (see Fig 5). IMPORTANT NOTES Remember to observe all safety warnings when operating the heater on auto setting unattended or attended . If the mains supply to the heater is interrupted, the timer clock will stop until power is restored ; reset the time of day to ensure correct ON and OFF times. Fig. 3 11 15 13 12 14 O I Fig. 4 Fig. 5 11 O 12 13 15 I 14 Cleaning WARNING – ALWAYS DISCONNECT FROM THE POWER SUPPLY BEFORE CLEANING THE HEATER. Do not use detergents, abrasive cleaning powder or polish of any kind on the body of the heater. Allow the heater to cool, then wipe with a dry cloth to remove dust and a damp cloth (not wet) to clean off stains. Be careful not to allow moisture into the heater. Recycling For electrical products sold within the European Community. At the end of the electrical products useful life it should not be disposed of with household waste. Please recycle where facilities exist. Check with your Local Authority or retailer for recycling advice in your country. After Sales Service Your product is guaranteed for three years from the date of purchase. Within this period, we undertake to repair or exchange this product free of charge (subject to availability) provided it has been installed and operated in accordance...

Ce manuel est également adapté pour les modèles :
Ventilateurs - ARLWP800TI (200.08 kb)
Ventilateurs - DXLWP400 (200.08 kb)
Ventilateurs - DXLWP400TI (200.08 kb)
Ventilateurs - DXLWP800 (200.08 kb)

Écrivez votre propre critique du dispositif



Texte du message
Votre nom :
Entrez les deux chiffres :
capcha





catégories