Évaluations - 3, GPA: 4.3
(
)
)
|
Par ce dispositif a également d'autres instructions :
Facilité d'utilisation
FF/M. During rewind, hold continued Playing/searching at various speeds Playback options Operation Play at high speed • During playback, press M FF or m REW on the remote commander. • During playback, hold down M FF/M or m REW/m. When you release the button, normal playback resumes. Play at twice the normal speed During playback, press .2. Play in slow motion During playback, press y SLOW. Play frame by frame During pause, press M FF or m REW on the remote commander. Hold down M FF or m REW to play one frame each second. Rewind and start play During stop, press H PLAY on the VCR while holding down m on the VCR. To resume normal playback Press H PLAY. Using the shuttle ring (SLV-SE800D1/D2/E and SX800D only) With the shuttle ring, you can operate a variety of playback options. There are two ways for using the shuttle ring, normal mode and jog mode. To use the shuttle ring in normal mode During playback or pause, turn the shuttle ring clockwise or anticlockwise. Each change in the shuttle ring position changes the playback mode in the following way. Pause Slow motion in reverse Normal speed in reverse Double speed in reverse Slow motion Double speed Normal speed (Initial speed) High speed in High speed reverse Playing/searching at various speeds To use the shuttle ring in jog mode Use this mode for frame-by-frame playback. Press JOG to enter the jog mode. The JOG button lights up. If you change to the jog mode during any playback mode, playback pauses so you can see a still picture. Each change in the shuttle ring position shifts the picture one frame. To shift frames in reverse, turn the shuttle ring anticlockwise. The frame shift speed depends on the speed you turn the shuttle ring. To resume normal mode, press JOG again. The JOG button turns off. Tip • Adjust the picture using the TRACKING +/– buttons if: – Streaks appear while playing in slow motion. – Bands appear at the top or bottom while pausing. – The picture shakes while pausing. To set tracking to the centre position, press both buttons (+/–) at the same time. Notes • The sound is muted during these operations. • In the LP mode, noise may appear or there may be no colour. • If the playback mode mark doesn’t appear on the TV screen, press DISPLAY. Additional Operations Playing/searching at various speeds Setting the recording duration time After you have started recording in the normal way, you can have the VCR stop recording automatically after a specified duration. zREC 1 While recording, press z REC. The indicator appears in the display window. SP VIDEO OPC 2 Press z REC repeatedly to set the duration time. Each press advances the time in increments of 30 minutes. 0:30 1:00 5:30 6:00 Normal recording The tape counter decreases minute by minute to 0:00, then the VCR stops recording and turns off automatically. To extend the duration Press z REC repeatedly to set a new duration time. To cancel the duration Press z REC repeatedly until the indicator disappears and the VCR returns to the normal recording mode. To stop recording To stop the VCR while recording, press x STOP. Note • You cannot display the current tape time in the display window when setting the recording duration time. Setting the recording duration time Synchronized Recording (SLV-SE800D1/D2/E and SX800D only) You can set the VCR to automatically record programmes from equipment such as a satellite tuner by connecting the equipment to the DECODER/LINE-3 IN connector. The connected equipment must have a timer function for this feature to work. When the connected equipment turns on, the VCR also automatically turns on and starts recording a programme from DECODER/LINE-3 IN. How to connect for Synchronized Recording Connect the DECODER/LINE-3 IN connector of the VCR to the TV Scart connector of the satellite tuner. Then connect the LINE-1 (TV) connector to the TV. Scart cable (not supplied) Additional Operations DECODER/t LINE-3 IN i LINE-1 (TV) TV Scart connector Satellite tuner, etc. Scart cable (not supplied) Scart (EURO-AV) : Signal flow continued Synchronized Recording (SLV-SE800D1/D2/E and SX800D only) Recording programmes using the Synchronized Recording function Before you start... • Insert a tape with its safety tab in place. Make sure the tape is longer than the total recording time. • Set DECODER/LINE3 to LINE3 in the OPTIONS-2 menu (see page 79). SYNCHRO REC 1 2 3 4 5 6 7 8 9 0 SP/LP INPUT SELECT PROG +/– 1 Press INPUT SELECT or PROG +/– to display “L3” in the display window. 2 Set the timer on the connected equipment to the time of the programme you want to record, then turn it off. 3 Press SP/LP to select the tape speed. 4 Hold down SYNCHRO REC for more than two seconds. The SYNCHRO REC button lights up and the VCR stands by for recording. The VCR automatically turns on and starts recording when it receives an input signal from the connected equipment. The VCR automatically stops recording when the tape reaches the end or when the connected equipment stops transmitting an i...
Ce manuel est également adapté pour les modèles :joueurs de magnétoscope / vidéo - SLV-SE600A (1.13 mb)
joueurs de magnétoscope / vidéo - SLV-SE600E (1.13 mb)
joueurs de magnétoscope / vidéo - SLV-SE650D (1.13 mb)
joueurs de magnétoscope / vidéo - SLV-SE700D1 (1.13 mb)