Évaluations - , GPA: ( )

Instructions Empire Comfort Systems, Modèle SR-10-3

Fabricant : Empire Comfort Systems
Taille : 2.81 mb
Nom Fichier : 7ef197cd-13da-44e7-bc46-9ac2f06b1304.pdf

Langue d'enseignement:

Le document est chargé, s'il vous plaît patienter

Téléchargez votre Fermer

Le document est chargé, s'il vous plaît patienter

Téléchargez votre Fermer

USE OF ANY OTHER PARTS COULD CAUSE INJURY OR DEATH. SR-10 PARTS VIEW SR-30 PARTS VIEW OPTIONAL BLOWER INSTALLATION INSTRUCTIONS (continued) Wiring The appliance, when installed, must be electrically grounded in accordance with local codes or, in the absence of local codes, with the National Electrical Code, ANSI/NFPA 70, if an external electrical source is utilized. This appliance is equipped with a three-prong [grounding] plug for your protection against shock hazard and should be plugged directly into a properly grounded three-prong receptacle. Do not cut or remove the grounding prong from this plug. For an ungrounded receptacle, an adapter, which has two prongs and a wire for grounding, can be purchased, plugged into the ungrounded receptacle and its wire connected to the receptacle mounting screw. With this wire completing the ground, the appliance cord plug can be plugged into the adapter and be electrically grounded. CAUTION: Label all wires prior to disconnection when servicing controls. Wiring errors can cause improper and dangerous operation. Verify proper operation after servicing. Blower Motor The blower motor does not have oiling holes. Do not attempt to oil the blower motor. Blower Wheel The blower wheel will collect lint and could require periodic cleaning. If the air output decreases or the noise level increases, it indicates a dirty blower wheel. To clean blower wheel: 1. Turn OFF gas supply to the heater. 2. Turn OFF electrical supply to the heater. 3. Remove lower louver from casing assembly (2 screws). 4. Remove reflector from casing assembly (2 screws). 5. Remove upper louver from casing assembly (2 screws). 6. Clean blower wheel with a vacuum cleaner. 7. As parts are being replaced in reverse order, check for gas leaks at all gas connections before lower louver is replaced onto casing assembly. WARNING: Unplugging of blower accessory will not stop the heater from cycling. To turn off gas to the unvented heater: Push in gas control knob slightly and turn clockwise to "OFF." Do not force. If any of the original wire as supplied with the appliance must be replaced, it must be replaced with type 125°C wire or its equivalent. PARTS LIST INDEX NUMBER PART NUMBER DESCRIPTION 1 R-2396 BLOWER (INCLUDES MOTOR, FAN, AND FAN HOUSING) 2 R-2522 ON/OFF SWITCH 3 R-2395 WIRE ASSEMBLY 4 8720161 BUSHING - HEYCO #SR5KN4 5 VF-068 CORD SET ASSEMBLY 6 SR-195 BLOWER PAN (SR-18) 7 8520141 RUBBER GROMMET (4 REQUIRED) 8 8520142 BRASS BUSHING (4 REQUIRED) NOT SHOWN SR-218 HARDWARE PACKAGE PH: 1-618-233-7420 PH: 1-800-851-3153 FAX: 1-618-233-7097 FAX: 1-800-443-8648 E-MAIL: info@empirecomfort.com WEB SITE: Empire Comfort Systems, Inc. Nine Eighteen Freeburg Ave. Belleville, Illinois 62220-2623 Page 2 16942-0-0506 TABLA DE CONTENIDO SECCION PAGINA Importante Informacion de Securidad ..........................................................................3 Informacion de Securidad para Usuarios de Gas Propano (LP) ...................................4 Introduccion ..................................................................................................................5 Especificaciones ............................................................................................................5 Vapor de Agua: Un Subproducto de Calentadores de Cuarto sin Emision ...................6 Provisiones para Combustion de Aire Adecuados ........................................................6 Abastecimiento de Gas .................................................................................................7 Espacios Libres del SR-6 ..............................................................................................8 Espacios Libres del SR-10 .........................................................................................8-9 Espacios Libres del SR-18 ............................................................................................9 Espacios Libres del SR-30 ..........................................................................................10 Installacion para Montaje en Pared ........................................................................10-11 Installacion de Base de Piso Opcional ........................................................................12 Instrucciones de Encendido ........................................................................................13 Caracteristicas de la Llama de Quemador Principal ...................................................14 Caracteristicas de la Llama del Piloto ........................................................................15 Operacion de la Llama de Quemador Principal ..........................................................15 Mantenimiento del Aparato ........................................................................................16 Informacion de Reparacion para Personas Calificadas de Servicio ............................16 Lista de Partes de los SR-6 y SR-10 ....................