Log:
Évaluations - 3, GPA: 4 ( )

Instructions Petsafe, Modèle DRINKWELL HY-DRATE PFD17-12900

Fabricant : Petsafe
Taille : 221.54 kb
Nom Fichier :
Langue d'enseignement: en
Aller à la télécharger



Facilité d'utilisation


1a). Level of water above the hy·drate™ will give a rippling or bubbling effect on top of the water. Both options provide continuous movement and filtration for cleaner, fresher water. Now, adjust the flow control on the pump based on the size of the bowl, desired flow of water or to reduce water splattering from the bowl (See Fig. 1a & 1c). After beginning operation of the hy·drate™, simply allow your pet to adjust at his or her own pace. Some pets may take several days or longer to begin use. After your pet is acclimated to the hy·drate™, continue to replenish your pet’s drinking water frequently for maximum hydration. It is not recommended that any appliance be left running unattended for a prolonged period of time as the water may get consumed or evaporate, thus causing the motor to run dry and can reduce life of the pump. Cleaning Instructions: The hy·drate™ upper shell, lower shell with suction cups and pump connector are dishwasher safe at low temperatures or can be hand washed with warm soapy water. THE PUMP IS NOT DISHWASHER SAFE! To remove pump from upper shell push in rubber fitting towards pump to release. Thread pump power cord through suction cup loop and pump cord pass-through (See Fig. 1a & 1b). The hy·drate™ pump should be disassembled and cleaned every two weeks (See Fig. 2 & 3). To remove “hard water” mineral build-up soak disassembled pump in regular white vinegar for several minutes and rinse thoroughly. Once the parts are clean, reassemble the pump by replacing the impeller, stator, flow control (See Fig. 4) and the intake plate. Thread pump power cord back through pump cord pass-through and suction cup loop, and position pump onto the pump connector post in the upper shell (See Fig. 1a & 1b). Grasp the rubber fitting and pull through hole in upper shell until it snaps into place sealing the opening (See Fig. 1a & 1b). The length of the pump power cord may need to be adjusted by pulling either end to position pump onto pump connector post. The filter should be replaced every 2 -4 weeks to maintain filtered, fresh and clean water. Small food particles and hair must be cleaned between the intake and filter as needed to maintain strong current flow. IMPORTANT: Warranty may be voided if pump is not cleaned regularly. Product Specifications: Voltage/Power Consumption 120VAC 60Hz 3.3 WATTS 12 Volts low-level power adapter output Accessories: To purchase replacement parts or accessories, contact PetSafe® Customer Care Center at 1-800-732-2677 or by visiting Replaceable Filters, 3-pack PFD17-12905 Fig. 2 Pump Impeller Stator Flow Control Intake Plate With your thumb and forefinger, gently squeeze the sides of intake plate, and pull off. Remove the flow control, stator and impeller. To remove impeller use a fingernail to lift out; it is held in magnetically. Replaceflowcontrolbyplacing post into opening onthepumpmotor.AlignflowcontrolknobtoopeningonintakeplateandattachintakeplateFig. 4Fig. 3 Clean with warm soapy wa...

Ce manuel est également adapté pour les modèles :
purificateurs d'eau - DRINKWELL HY-DRATE PFD17-12899 (221.54 kb)
purificateurs d'eau - DRINKWELL HY-DRATE PFD17-12901 (221.54 kb)
purificateurs d'eau - DRINKWELL HY-DRATE PFD17-12902 (221.54 kb)
purificateurs d'eau - DRINKWELL HY-DRATE PFD17-12903 (221.54 kb)

Écrivez votre propre critique du dispositif



Texte du message
Votre nom :
Entrez les deux chiffres :
capcha





catégories