Printed instruc tions are on the resin bed cleaner bottle. IF YOU HAVE QUESTIONS ABOUT CLEANING AND MAINTAINING YOUR SOFTENER, CALL TOLL FREE, NUMBER 1-800-426-9345. 15 SECTION 3 CARE OF YOUR SOFTENER I I 3C. KEEP THE SOFTENER FROM FREEZING If the softener is installed where it could freeze DRAIN WATER FROM THE (summer cabin, lake home, etc.), you must drain all SOFTENER water from it to stop possible freeze damage. To drain the softener: 1. Close the shut-off valve on the house main water pipe,

BE SURE THE FLOW PLUG WITH THE LARGEST CENTER HOLE IS LOCATED IN THE NOZZLE & VENTURI HOUSING. other equipment is needed. Your local Sears store has trained people to help you with iron water problems. If your water supply has clear water iron, even though less than the maximum allowed, regular resin bed cleaning is needed. Sears has resin bed cleaner, Stock No. 42-34426 for this. Clean the bed at least every 6 months. If iron shows up in the soft water before 6 months, clean more often. Printed

Does the time display show the correct time of day? --If display is blank, check power source to the softener. --If time is flashing, power was off for over 24 hours. The softener resumes normal operation but regenerations occur at the wrong time. --If an error code (Example: Err3) shows in the face plate display, go to AUTOMATIC ELECTRONIC DIAGNOSTICS. ° Plumbing bypass valve(s) must be in Full Service position. 3. The inlet and outlet pipes must connect to the softener inlet and outlet respect

MD Single Head P/N 169110 (1 Pack) Replaces P/N EV927401 MD Dual Head Assembly* P/N 169111 (1 Pack) Designed for use with Replaces P/N EV927402 MD-CN & MD-CE filter Designed for use with cartridges. MD-CN & MD-CE filter cartridges. MD Triple Head Assembly* P/N 169112 (1 Pack) Replaces P/N EV927403 Designed for use with MD-CN & MD-CE filter cartridges. OPERATION TIPS • Change cartridges: - on a regular 6 month preventative maintenance basis - when the pressure gauge indicates a pressure less than

Pentair Water Treatment/Plymouth Products, however, shall not be liable for damages or delays caused by any defective material or workmanship, or by failure of any parts due to normal wear and tear. Pentair Water Treatment/Plymouth Products will not be responsible for products which malfunction due to user neglect or unauthorized modification. NOTE: Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. Similarly, some states do

DO NOT ATTEMPT TO LIFT IT BY YOURSELF. DO NOT DROP AND BREAK THE TANK. . Stand the tank upright and replace the bottom distributor assembly. Temporarily, plug the top end of the distributor (use rag, etc.) to prevent accidental mineral spills into it. 1 Using a large neck funnel (FIG. 6), first add 17 Ibs. of gravel, followed by 10 Ibs. of filter sand. Next, add the 1 cu. ft. of activated carbon. Use water sparingly to assist carbon flowthrough the funnel. NOTE: Be sure the bottom distributor is

The neutralized or non-acid water then flows into the house water pipes. Because the neutralite does dissolve, you have to add new mineral at least once each year, and sometimes more often (see page 14). TASTE AND ODOR FILTER The taste and odor filter is filled with activated carbon. As water flows into and DOWN through the filter (FIG. 5), the tastes and/or odors are adsorbed and held by the carbon. Water without bad tastes or odors goes into the house pipes. When the activated carbon no longer

STEPS TO ADD MINERAL 1. Press the face plate BACKWASH NOW button [] and hold for 3 seconds, until RCHG begins to flash in the display. 2. When water begins to flow from the valve drain hose, place the bypass valve(s) in BYPASS position.., see FIG. 8, page 18. CAUTION: BE SURE TO DO STEPS 1AND2 AS INSTRUCTED, TO RELIEVE WATER PRESSURE IN THE TANK. 3. Unplug the transformer at the wall outlet. 4. Carefully, pull the 2 clips (key #41, page 26) at the inlet and outlet fittings. Slide the adaptors, o

CGS-23 20" Parallel Housing Foodservice System Housing for Drop-In Cartridges CGS-23 20" Dual Parallel Housing: DEV9100-23CGS-23 20" Dual Parallel Housing: DEV9100-23 20" low profile Slim Line dual bowl housing in Parallel configuration Manufactured of durable polypropylene and has excellent chemical resistance System includes pre-mounted water pressure gauge Equipped with a pressure relief button to relieve water pressure during cartridge changes Includes wall mounting bracket and hardware for

Allow 2-1/2” clearance below the cartridge for easy cartridge replacement Make sure O-ring on bowl is sufficiently lubricated Always screw on bowls by hand; do not use a housing wrench Change cartridges on a regular 6 month preventative maintenance program Change cartridges when capacity is reached or when pressure decreases Always inspect O-ring; change and/or lubricate if necessary Always flush the filter cartridge at time of installation and cartridge change For foodservice applications Drop-