Évaluations - 3, GPA: 4
(
)
)
|
Par ce dispositif a également d'autres instructions :
Facilité d'utilisation
INSTALLING THE WATER LINE Connecting the water line to the Refrigerator. There are several items that you need to purchase to complete this connection. You may fi nd these items sold as a kit at your local hardware store. 1 2 Example) The slope is about 2 mm (0.08 inch) as shown below. - Rotate the Height Adjuster to -2.0 to reduce the door slope. Slope Reference plane 3 Water fi lter Hex wrench Fastener Compression fi tting Compression nut 1 Cold water line 2 Pipe clamp 3 Water line installation kit 4 Shut off valve .............................................................. ........................................................................................ 012 SOEPTETRINATGIN UGP Setting up _11 1. Slip the compression nut through the supplied plastic tubing . 2. Tighten the compression nut onto the 6.35 mm compression fi tting. - If you are using copper tubing, slip the compression nut (not included) and ferrule (not included) on copper tubing (not included) as shown. - If you are using plastic tubing , insert the molded end(Bulb) of the plastic tubing into the compression fi tting. Do not use without the molded end(Bulb) of the plastic tubing . 3. Tighten the compression nut onto the compression fi tting. Do not over-tighten the compression nut . 4. Turn water on and check for any leakage. Only connect the water line to a drinkable water source. If you have to repair or disassemble the water line, cut off 6.35 mm of the plastic tubing to make sure you get a snug, leak-free connection. Installing the water fi lter. 1. Remove the water fi lter cover 1 . 2. Remove the fi xed cap by turning it counter clockwise. Keep the cap in a safe place for later use if you don’t use the fi lter. 3. Remove the water fi lter from the box and put a replacement indicator sticker on the fi lter as shown. Place the sticker on the fi lter that dates six months in the future. For example, if you install the water fi lter in March, put the “SEP” sticker on the fi lter to remind you to replace it in September. That way you’ll know when it is time to replace the fi lter. Normally, a fi lter life is about 6 months. 4. Remove the fi lter cap and insert the fi lter into the fi lter housing. 5. Slowly turn the water fi lter 90. clockwise to align with the printing mark on the cover, locking the fi lter in position. Make sure to align the water fi lter label mark with center of cover fi lter printing as illustrated. Remember, do not overtighten. You should remove the right side upper glass shelf before installing the water fi lter. Removing any residual matter inside the water supply line after installing the water fi lter. 1. Turn ON the main water supply & turn OFF the valve to the water supply line. 2. Run water through the dispenser until the water runs clear (approx. 6-7 minutes). This will clean the water supply system and remove air from the lines. 3. Additional fl ushing may be required in some households. 4. Open the Refrigerator door and make sure there are no water leaks coming from the water fi lter. Be sure to fl ush the dispenser thoroughly or water may leak from it. This is due to the fact that there is still air in the line. Plastic tubing (Supplied) Ferrule (Not supplied) Compression nut (6.35 mm) (Supplied) Compression fi tting (Supplied) Bulb Compression nut (6.35 mm) (Not supplied) Copper tubing or Plastic tubing (Not supplied) (Not supplied) Household water line Refrigerator 1 2 3 Sticker (month indicator) • 6.35 mm compression nut • copper tubing • plastic tubing • ferrule Turn until the label is Separation aligned. of red cap. Cover fi lter 4 5 ............................................................................................................................ ........................................................................................ 12_ Operating Operating the SAMSUNG refrigerator USING THE CONTROL PANEL Energy Saver Button For better energy effi ciency, press the Energy Saver button( ). If condensation occurs on the doors, turn the Energy Saver function off. Freezer/ Hold 3 sec for Power Freezer Button Press the Freezer/Hold 3 sec for Power Freezer button( ) to set the Freezer to your desired temperature. You can set the temperature between -14 .C and -22 .C. Press and hold the Freezer/Hold 3 sec for Power Freezer button for 3 seconds, to speed up the time needed to freeze products in the Freezer. It can be helpful if you need to quickly freeze easily spoiled items or if the temperature in the Freezer has warmed dramatically (For example, if the door was left open). When you use this function the energy consumption of the refrigerator will increase. Remember to turn it off when you don’t need it and return the freezer to your original temperature setting. When you have enough ice, just press and hold the button for 3 seconds again to cancel the Power Freeze mode. Power Freezer mode must be activated before putting large stuff in freezer compartment at least 20 hours before. Alarm/ H...
Ce manuel est également adapté pour les modèles :Réfrigérateurs - RFG23DERS (23.27 mb)