Lack of maintenance or misuse of the unit will VOID warranty. Please fill out the registration card and send it to the factory. CABINET LOCATION GUIDELINES 1) Install the unit on strong and leveled surfaces -unit may make unpleasant noises if surface is uneven -unit may malfunction if surface is uneven 2) Install the unit in an indoor, well-ventilated area -unit performs more efficiently in a well-ventilated area -for best performance, please maintain clearance of 4" on the back of the unit -out

............................................................Maintenance Page 7......................................................Temperature Control Instructions Page 9.........................................................................Refrigerator Settings Page 10..............................................................................Freezer Settings Page 11...............................................................................Troubleshooting LIMITED WARRANTY Jimex Corp. w

Please read the manual thoroughly prior to equipment set-up, operation and maintenance. Failure to comply with regular maintenance guidelines outlined in this manual may void warranty. MUST READ!!! 1575 Zephyr Avenue Hayward, CA 94544 (800) 314-4477 (510) 477-3400 f: (510) 477-3413 TABLE OF CONTENTS Page 2...............................................................ColdTech Limited Warranty Page 3.........................................................................................Installat

= minutes max = maximum hr. = hours N/A = not applicable Warning: Do not change the default settings of your ColdTech unit without consulting a qualified service technician or theColdTech service department. -9 Applicable to Models: CFD-1F, CFD-2F, CFD-3F ColdTech® Freezer Settings Temperature set to -4 F Parameter Function Set Range Default E1 Lower Setpoint Limit -40 F ~ set temp -10 F E2 Higher Setpoint Limit set temp ~ 120 F 20 F E3 Hysteresis, temp variance 1 ~ 18 F 10 F E4 Comp. start dela

ColdTech recommends cleaning the condenser coil and fins at least once per month. Clean with a commercial condenser coil cleaner, available from any kitchen equipment retailer. Brush the condenser fins from top to bottom, not side to side. After cleaning, straighten any bent condenser fins with a fin comb. CLEANING THE FAN BLADES AND MOTOR If necessary, clean the fan blades and motor with a soft cloth. If it is necessary to wash the fan blades, cover the fan motor to prevent moisture damage. CLE

Plug in power cord. Thermostat set too high. Set thermostat to lower temperature. Cabinet in defrost cycle. Wait for defrost cycle to finish. Condensing unit runs for Excessive amount of warm product Allow adequate time for long periods of time. placed in cabinet. product to cool down. Prolonged door opening or door ajar. Ensure doors are closed when not in use. Avoid opening doors for long periods of time. Door gasket(s) not sealing properly. Ensure gaskets are snapped in completely. Remove gas

0 (02/23/2005) BRIGGS & STRATTON POWER PRODUCTS GROUP, LLC JEFFERSON,WISCONSIN, U.S.A. Owner’s Manual Manual del Propietario Questions? Help is just a moment away! Preguntas? La ayuda es justa un momento lejos! Call: Generator Helpline / Llamada: Generador Helpline 1-800-743-4115 M-F 8-5 CT web: PowerBOSS™ is a trademark of Briggs & Stratton Power Products. PowerBOSS™ es una marca registrada de Briggs & Stratton Power Products. Model / Modelo 030222 (5000W) Before using this product, read this m

To decrease the temperature (colder), turn clockwise. To increase the temperature (warmer), turn counter-clockwise - see diagram LOADING PRODUCT The bin dividers have been installed at the factory for your conveniance. Feel free to reposition the dividers as you see fit. To remove the bin dividers, simply push the divider towards the back wall until the front of the divider is removed from the positioning holes. To install, position the divider to the desired holes, making sure that the pressure

Failure to comply with regular maintenance guidelines outlined in this manual may void warranty. MUST READ!!! 1575 Zephyr Avenue (800) 314-4477 (510) 477-3400 f: (510) 477-3413 LIMITED WARRANTY Jimex Corp. warrants to the original purchaser the ColdTech unit sold and all parts thereof to be free from defects in material or workmanship, under normal use and service for a period of one (1) year from the date of purchase. In addition to the warranty set forth above, Jimex Corp. warrants the hermeti

3) Do not put your hands under the unit when the unit is required to be moved. 4) When the unit is not in use for a long period of time, please unplug the unit from the outlet. 5) After unplugging the unit, wait at least 10 minutes before re-plugging it. Failure to do so could cause damage to the compressor. 1) To minimize shock and fire hazards, please do not plug or unplug the cord with wet hands. 2) During maintenance and cleaning, please unplug the unit. 1) To minimize shock and fire hazards