Log:
Évaluations - 2, GPA: 4 ( )

Instructions Grizzly, Modèle 5378-20

Fabricant : Grizzly
Taille : 1.38 mb
Nom Fichier : M0148.pdf
Langue d'enseignement: enesfr
Aller à la télécharger



Facilité d'utilisation


3 FUNCTIONAL DESCRIPTION 9 1. Side handle 2. Depth guage 3. Clamping lever 4. Hammer/Drill lever 5. Lock button 6. Trigger 7. Forward/Reverse lever 8. Speed selector 9. Chuck 4 3 5 7 2 1 68 The grounding prong in the plug is connected through the green wire inside the cord to the grounding system in the tool. The green wire in the cord must be the only wire connected to the tool's grounding system and must never be attached to an electrically “live” terminal. Your tool must be plugged into an appropriate outlet, properly installed and grounded in accordance with all codes and ordinances. The plug and outlet should look like those in Figure A. Double Insulated Tools: Tools with Two Prong Plugs Tools marked “Double Insulated” do not require grounding. They have a special Improperly connecting the groundingwire can result in the risk of electric shock. Check with a qualifi ed electrician if you are in doubt as to whetherthe outlet is properly grounded. Donot modify the plug provided withthe tool. Never remove the groundingprong from the plug. Do not use thetool if the cord or plug is damaged.If damaged, have it repaired by aMILWAUKEE service facility beforeuse. If the plug will not fi t the outlet, have a proper outlet installed by aqualifi ed electrician. GROUNDING WARNING Grounded Tools: Tools with Three Prong Plugs Tools marked “Grounding Required” have a three wire cord and three prong grounding plug. The plug must be connected to a properly grounded outlet (See Figure A). If the tool should electrically malfunction or break down, grounding provides a low resistance path to carry electricity away from the user, reducing the risk of electric shock. Fig. A double insulation system which satisfies OSHA requirements and complies with the applicable standards of Underwriters Laboratories, Inc., the Canadian Standard Association and the National Electrical Code. Double Insulated tools may be used in either of the 120 volt outlets shown in Figures B and C. Fig. B Fig. C Specifications Symbology Capacities Tool Drill Only (steel or wood) Rotary Hammer (concrete) Cat. No. Volts AC A No Load RPM No Load Blows per Minute Twist Drill Bit Carbide Tipped Percussion Bit 5378-20 and 5378-21 120 7.5 Low 0 - 1350 High 0 - 2500 22,000 40,000 1/2" - 1-1/2" 5/8" Double Insulated BPM Blows per Minute (BPM) Underwriters Laboratories, Inc. Volts Alternating Current Amps No Load Revolutions per Minute (RPM) Canadian Standards Association Mexican Approvals Marking 45 EXTENSION CORDS Grounded tools require a three wire extension cord. Double insulated tools can use either a two or three wire extension cord. As the distance from the supply outlet increases, you must use a heavier gauge extension cord. Using extension cords with inadequately sized wire causes a serious drop in voltage, resulting in loss of power and possible tool damage. Refer to the table shown to determine the required minimum wire size. The smaller the gauge number of the wire, the greater the capacity o...

Ce manuel est également adapté pour les modèles :
Perceuses et shuropopverty - 5378-20 (1.38 mb)
Perceuses et shuropopverty - 5378-20 (1.38 mb)
Perceuses et shuropopverty - 5378-20 (1.38 mb)
Perceuses et shuropopverty - 5378-21 (1.38 mb)

Écrivez votre propre critique du dispositif



Texte du message
Votre nom :
Entrez les deux chiffres :
capcha





catégories