Évaluations - 1, GPA: 5
(
)
)
|
Facilité d'utilisation
REQUIREMENTS OF THE PROVINCIAL MPB33 H2009 AUTHORITIES HAVING JURISDICTION MPB35 H2011 AND IN ACCORDANCE WITH THE REQUIREMENTS OF THE CAN/ MPB40 H2013 CGA-B149.1 INSTALLATION CODE. MPB45 H2015 LA CONVERSION DEVRA ETRE Millivolt SIT SystemsEFFECTUEE CONFORMEMENT AUX Propane Gas to Natural GasConversion Kits RECOMMANDATIONS DES AUTORITES Models Catalog No. PROVINCIALES AYANT JURIDICTION ET CONFORMEMENT AUX EXIGENCES MPB33 H2010 DU CODE D'INSTALLATION CAN/ MPB35 H2012 CGA-B149.1. MPB40 H2014 Gas conversion kits are available to adapt MPB45 H2016 your appliance from the use of one type of Table 9: Millivolt Conversion Kits gas to the use of another. These kits contain all the necessary components needed to complete the task including labeling that must be affi xed to ensure safe operation. Kit part numbers are listed here and the following steps detail the conversion procedure. Refer to the instructions provided with the conversion kit when performing any gas conversion. Electronic SIT Systems Natural Gas To Propane Gas Conversion Kits Models Catalog No. MPB33 H8632 MPB35 H8634 MPB40 H8636 MPB45 H8638 Electronic SIT Systems Propane Gas To Natural Gas Conversion Kits Models Catalog No. MPB33 H8631 MPB35 H8633 MPB40 H8635 MPB45 H8637 Table 10: Electronic Conversion Kits INSTALLATION INSTRUCTIONS Step 1. TURN OFF THE GAS SUPPLY TO THE APPLIANCE and disconnect power supply at the circuit breaker. Ensure appliance is cold. CAUTION: THE GAS SUPPLY SHALL BE SHUT OFF PRIOR TO DISCONNECTING THE ELECTRICAL POWER, BEFORE PROCEEDING WITH THE CONVERSION. ATTENTION: AVANT D’EFFECTUER LA CONVERSION, COUPEZ D’ABORD L’ALIMENTATION EN GAZ, ENSUITE, COUPEZ L’ALIMENTATION ELECTRIQUE. Step 2. Open the lower control compartment door (see Figure 19 on Page 13) by pushing on the right top corner of the door (the door is hinged at the bottom). [Optional] Remove the control compartment door by sliding the hinge pin, located at the door’s left side, to the right until it disengages from the left corner post hole. Pull the control compartment door diagonally to the left, away from the fi replace. Step 3. Remove the front glass door/frame from the appliance (see Page 19). NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE. 24 NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE. LENNOX HEARTH PRODUCTS • MERIT PLUS® B-VENT GAS FIREPLACES (MPB33/35/40/45) • INSTALLATION INSTRUCTIONS Step 4. Carefully remove the logs. Exercise care so as not to break the logs. Step 5. Refer to Figures 26, 27, or 28. A. Remove the grate and sub fl oor. B. Remove the two (2) screws securing the burner assembly. C. Remove the burner assembly with attached venturi tube. MILLIVOLT AND ELECTRONIC IGNITION SYSTEM APPLIANCES Step 6. SIT Systems—Refer to Figure 37 and the instructions provided with the SIT Regulator Conversion Kit. Using a Torx T20 driver to remove and discard the pressure regulator mounting screws (two screws for electronic models, three screws for millivolt models), pressure regulator tower, the ...
Ce manuel est également adapté pour les modèles :Cheminées - MERIT PLUS MPB3328CNE-B (2.39 mb)
Cheminées - MERIT PLUS MPB4540CNM-B (2.39 mb)
Cheminées - MERIT PLUS MPB4540CNE-B (2.39 mb)
Cheminées - MERIT PLUS MPB4035CNM-B (2.39 mb)