A water shut-off valve should be installed on the incoming water line in a convenient location (Use a low restriction type valve, such as a 1/4-turn ball valve, to avoid loss of water flow thru the valve. 5. NSF requires that the brewer be able to be moved for cleaning underneath. A flex line or loops of copper tubing will satisfy this requirement. 6. In some areas, local codes require a backflow preventer (check valve) to be installed on the inlet water line. If a back flow preventer is used, y

If the tank temperature is below the brew temperature, the brew will be delayed, going into the “Brew Wait” mode, with the brew light flashing. As soon as the correct temperature is reached the brew will commence with the brew light on continuously during the brew. When the brew begins the main warming station will be turned on automatically (if it is not already on). During the brew cycle, if the BREW key is pressed, it will be ignored. Only when the brew is complete can another brew be started

Thank You for purchasing this Bloomfield Industries appliance. Proper installation, professional operation and consistent maintenance of this appliance will ensure that it gives you the very best performance and a long, economical service life. This manual contains the information needed to properly install this appliance, and to use, care for and maintain or repair the appliance in a manner which will ensure its optimum performance. WARRANTY STATEMENT xi SPECIFICATIONS 1 FEATURES & OPERATING CO

IMPORTANT: DO NOT use steel wool, sharp objects, or caustic, abrasive or chlorinated cleansers to clean the brewer or decanters. 1. Disconnect brewer from electric power. Allow brewer to cool before cleaning. 2. Remove decanters. 3. Remove and empty brew chamber. 4. Remove the spray disk from the brew head: Press up on the spray disk ears, then turn the disk to the left to unlatch. Remove the gasket from inside the brew head. 5. Wipe inside of brew head and area around the brew head with a soft

Warmer models 8708, 8851, 8852, 8871 and 8872 are equipped with a cord and plug. They require a 115 - 125 volt 15 amp circuit (50/60 Hz, 2 wire plus ground, with NEMA 5-15R receptacle). WARNING: SHOCK HAZARD Brewer must be properly grounded to prevent possible shock hazard. DO NOT assume a plumbing line will provide such a ground. Electrical shock will cause death or serious injury. IMPORTANT: The ground prong of the plug is part of a system designed to protect you from electrical shock in the e

Place the appropriate EMPTY dispenser in place under the brew chamber. If a brew-thru lid is used, be sure the bypass opening in the lid is directly under the bypass nozzle. Press the “BREW” switch. The brew solenoid will open for an amount of time determined by the timer setting, admitting a measured quantity of water into the tank. Inlet water will displace a like amount of heated water from the tank. The hot water will be forced into the brew head where it will spray over the bed of grounds.

Do not wash floor or counter around this appliance with water or steam jet. Exposed surfaces of appliances can be hot to the touch and may cause burns. Warmer surfaces will be very hot when in use. Contact will cause severe injury. Do not operate any appliance if the control panel is damaged. Do not operate any appliance if the keypad section of an electronic control panel is torn or broken. Call your Bloomfield Agent for service. Protect electric power cords from damage and abrasion. Do not dra

O. Box 280 Verdi, NV 89439 telephone: 775-689-5707 fax: 775-689-5976 763 OPERATION MANUAL For Hot Plate-Style Decanter Warmer MODELS 8708 Dual In-Line Warmer 8851 Single Warmer 8852 Dual Warmer 8871 Single Warmer 8872 Dual Warmer Includes: Installation Use & Care Model 8702 Model 8852 Model 8871 NOTE: All warmers shown with optional 8900-Series Glass Decanters (available separately). 763 OPERATION MANUAL For Hot Plate-Style Decanter Warmer MODELS 8708 Dual In-Line Warmer 8851 Single Warmer 8852

1 FEATURES AND OPERATING CONTROLS FEATURES AND OPERATING CONTROLS POWER CORD WARMER PLATE WARMER SWITCH " I " INDICATES "ON" "O" INDICATES "OFF" OPTIONAL DECANTER (SHOWN FOR POSITION ONLY) SLIP-RESISTANT FEET Fig. 1 Features & Operating Controls Model 8852 shown. Features are similar for all models. 2 763 p/ n 77719 OpManual Decanter Warmers PRECAUTIONS AND GENERAL INFORMATION PRECAUTIONS AND GENERAL INFORMATION WARNING: ELECTRIC SHOCK HAZARD All servicing requiring access to non-insulated compo

2. All problems due to electrical connections not made in accordance with electrical code requirements and wiring diagrams supplied with the equipment. 3. Replacement of items subject to normal wear. Normal maintenance functions are not covered under warranty. 4. Proper attention, full care and maintenance will prolong the life of the machine. SHIPPING DAMAGE CLAIMS PROCEDURE SHIPPING DAMAGE CLAIMS PROCEDURE Note: For your protection, please note that the equipment in this shipment was carefully