Check to be sure that oven supports above the Warming Drawer location do not obstruct the required interior 23-1/2" depth and 9-1/4"height. 10-1/2" t 9" ^-2x4 or 2x2- Runners or Solid Bottom Including Handle Install '2x4 or 2x2 Anti-Tip Block Against Rear Cabinet Wall 9" From Floor to Bottom of Block Undercounter Installation (in inches) Note: When installing warming drawer with a cooktop, allow a 2" minimum from cooktop burner box bottom to top of cut-out. Important Installation Note:

– There is no way to level the drawer once it has been installed. Be sure supports are level. • The entire weight of the drawer is supported by the runners or solid floor and must be capable of supporting 150 lbs. 9" 2x4 or 2x2 Runners or Solid Bottom Install 2x4 or 2x2 Anti-Tip Block Against RearCabinet Wall 9" From Floor to Bottom of Block Step 2 Install Warming Drawer • Slide left corner of the drawer into the opening. • Push power cord into the hole leading to the outlet location. Thread the

• Wood screws and adhesive or other hardware for installing Tools and runners or shelf to support warmer drawer. Materials • 2 x 4 or 2 x 2 lumber for runners • 2 x 4 or 2 x 2 wood block for anti-tip security Required • Saw • Level • Drill and 1/16” bit • Phillips screwdriver Runners must be level, rigidly mounted and capable of supporting 150 pounds. Product Dimensions JXPN2 – Warming drawer pan kit. This kit includes supports and one full size and one half size pan with lids. The pans fit 27"

Disconnect electricity, remove thermostat and follow the directions for turning the altitude adjustment screw as shown in the label on each thermostat. (continued next page) PREPARATION (continued) Changing the Bin Door Panel You can easily change the color of the front panel on the storage bin door. Two colors are available: black and white. To change the panel: 1. Open the storage bin door. Remove the two screws on the top of the door which hold the handle. 2. Loosen the screws in both of the

IMPORTANT: For best results, use the entire contents of the bottle to clean the unit. See Care and Cleaning—Icemaker system section. Exterior surfaces Door handles and trim—Clean with a cloth dampened with soapy water. Dry with a soft cloth. Keep the outside clean. Wipe with a clean cloth lightly dampened with mild liquid dish detergent. Dry with a clean, soft cloth. Do not wipe the icemaker with a soiled dish cloth or wet towel. These may leave a residue that can damage the finish. Do not use s

5. Plug in the icemaker or reconnect power. Vacation To shut down the icemaker: and moving 1. Unplug the icemaker or disconnect power. 2. Remove all ice from the storage bin. 3. Shut off the water supply. 4. Remove the 2 screws in the lower access panel and the 2 screws from the base grille area of the front panel support. Pull forward to remove the lower access panel. 5. Disconnect the inlet and outlet lines to water valve. Allow these lines to drain and then reconnect to the valve. 6. Replace

WARNING: To reduce the risk of fire, electrical shock or injury when using your icemaker, follow basic precautions including the following: • Never allow children to operate, play with or crawl inside the icemaker. • Never clean icemaker parts with flammable fluids. The fumes can create a fire hazard or explosion. • Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance. The fumes can create a fire hazard or explosion. • Be sure your ice

2180919 Rev. A General Electric Company Pub. No. 49-6916-1 Louisville, KY 40225 Part No. 162D7745P003 6-97 CG Introduction Your new Monogram icemaker makes an eloquent statement of style, convenience and kitchen planning flexibility. Whether you chose it for its purity of design, practical features or assiduous attention to detail—or for all of these reasons—you’ll find that your Monogram icemaker’s superior blend of form and function will delight you for years to come. The Monogram icemaker was

Before installing, consult installation instructions packed with product for current dimensional data. Warranty Information: Full one-year warranty, in-home service, parts and labor.* Full five-year warranty, parts and labor on the compressor, evaporator and all connecting tubing.* *See written warranty for complete details. Note: The addition of a 3/4" thick front panel will result in a front to back depth of 24-1/16". For answers to your Monogram® GE Profile Performance Series,™ GE Prof

Before installing, consult installation instructions packed with product for current dimensional data. Warranty Information: Full one-year warranty, in-home service, parts and labor.* Full five-year warranty, parts and labor on the compressor, evaporator and all connecting tubing.* *See written warranty for complete details. Note: The addition of a 3/4" thick front panel will result in a front to back depth of 24-1/16". For answers to your Monogram® GE Profile Performance Series,™ GE Prof