5-year parts and 1-year labor warranty on compressor and 3-year parts and labor warranty on electronics. See the product manual for additional details. • Sanitation listed by NSF to Standard 6 and 18 (including dairy & alcohol) and safety listed by ETL to UL Standard (UL 471) and csA Standard (c22.2 No. 120). • White/Stainless, Black,Stainless and all Black finishes available. • International electrical configurations available. Ultra-1 Dimensions: 31.9”H x 7.9”W x 24.2”D (81 cm H x 20.1 c

Coffee can be brewed directly into the server without removing the cover when used with an appropriate Bunn® coffee brewer. Place the server on a warming stand to keep the beverage hot at remote locations. The spill-resistant design lessens the chance of hot beverage burns and splashes. USER NOTICES The notices on this server should be kept in good condition. Replace unreadable or damaged labels. CLOSEREMOVEONLYFORDAILYCLEANINGOPEN 12373.0000 12356.0000 BUNN-O-MATIC CORPORATION POST OFFICE BOX 3

: 39000.0008 Replacement Cartridge EQHP-ESPCRTG Product No.: 39000.1008 Rinza™ Milk Frother Cleaner Product No.: 39265.0000 (each) Product No.: 39265.0001 (6/case) Booster Pump Kit w/.357 hoses Product No.: 41815.1000 u Model Steamer Cup Heater Agency Listing eIVlJh c(Vl). RSF. 10/11 A8.4 Dimensions & Specifications Total Cubic Shipping Cord Model Product # Volts Amps Watts Measure Weight Attached Steamer 35800.0401 120 15.8 1900 7.6 ft3 62 lbs Yes/20A Plug (.22

In no event shall BUNN be liable for any other damage or loss, including, but not limited to, lost profits, lost sales, loss of use of equipment, claims of Buyer’s customers, cost of capital, cost of down time, cost of substitute equipment, facilities or services, or any other special, incidental or consequential damages. 392, AutoPOD, AXIOM, BrewLOGIC, BrewMETER, Brew Better Not Bitter, BrewWISE, BrewWIZARD, BUNN Espress, BUNN Family Gourmet, BUNN Gourmet, BUNN Pour-O-Matic, BUNN, BUNN with the

2. Remove circuit board and spacers (as required). 3. Remove all wires from the timer. 4. Attach all wires to the replacement timer board prior to installation to the component mounting bracket. Refer to FIG. 7 when reconnecting the wires. 5. Install new circuit board with spacers (as required) to the component mounting bracket. 6. Adjust the timer as described below. Timer Setting: NOTE: Prior to setting or modifying volumes, check that the brewer is connected to water supply, the tank is prope

6. Carefully bend the capillary tube so that the tube and bulb inside the tank are in a vertical position. NOTE: The capillary tube must be clear of any electrical termination and not kinked. 7. Fasten the new control thermostat to its bracket. 8. Refer to Fig. 7 when reconnecting the wires. 9. Adjust the control thermostat as required. BUNNOFF BLK to Tank Heater (100/120V) Thermal Fuse (230V) BLU/BLK to Limit Thermostat P2090.80 FIG. 7 CONTROL THERMOSTAT TERMINALS 37236 080504 Page 19 SERVICE (

10334 012609 3 CLEANING CAUTION - CLEAN AND SANITIZE YOUR ICED TEA/COFFEE DISPENSER DAILY 1. Twist the faucet wing nut in a clockwise direction and remove the faucet from the dispenser. 2. Thoroughly clean the entire inside surface of the dispenser and the faucet shank with the #00674.0000 brush using a mild detergent and water solution. Rinse the dispenser and shank with warm water. 3. Disassemble the faucet. The faucet cleaning procedure requires a 3-compartment sink. Thoroughly wash all fauce

5-year parts and 1-year labor warranty on compressor and 3-year parts and labor warranty on electronics. See the product manual for additional details. • Sanitation listed by NSF to Standard 6 and 18 (including dairy & alcohol) and safety listed by ETL to UL Standard (UL 471) and csA Standard (c22.2 No. 120). • White/Stainless, Black,Stainless and all Black finishes available. • International electrical configurations available. Ultra-1 Dimensions: 31.9”H x 7.9”W x 24.2”D (81 cm H x 20.1 c

All notices are to be kept in good condition. Replace any unreadable or damaged labels. Site preparation The dispenser must have at least four inches of space behind it. This space is needed for airflow, air filter removal, and cleaning. Minimal clearance is required between the dispenser sides and the wall or another appliance. The dispenser performs better if not placed near any heating appliance. Leave some space so the dispenser can be moved for cleaning. 41084 102709 INTRODUCTION Safety fir

6. Place the ON/OFF or SELECTOR switch in the “ON” position. 7. Momentarily press the start switch. CAUTION -The funnel contains hot liquids. Remove funnel slowly. 8. Carefully remove the brew funnel and discard the used filter when tea no longer drips from the funnel tip. 9. Place the ON/OFF or SELECTOR switch in the "OFF" position to prevent a false start. 10. Fresh tea is available at the faucet. 10145 072600 Page 7 TROUBLESHOOTING A troubleshooting guide is provided to suggest probable cause