HALO HEAT … a controlled, uniform heat source that gently holds and surrounds food for better appearance, taste, and longer holding life. . Holds and displays hot food fresh and moist for hours. . SELF-SERVICE HOT DISPLAY CASE — Curved glass styling. — Thermostatically controlled heat source radiates from the base of each shelf. — Top shelf incorporates thermal kinetic glass technology to provide an evenly heated display surface. — Bottom shelf is heated by an aluminum plate with a resistive hea

Donotinstallaheateddisplaycasenearacoldairsourcesuchasafreezer,airconditioningvents,orinanyareawhereoutsideairfluctuationcanaffectperformance. WEIGHTMODELNETSHIPEC2-48305lb(138kg)380lb(172kg) EC2SYS-48350lb(159kg)425lb(193kg) EC2-48/P305lb(138kg)380lb(172kg) EC2SYS-48/P350lb(159kg)425lb(193kg) CRATEDDIMENSIONS(EST.):HXWXDEC2-48:45"x60"x55"(1143mmx1524mmx1397mm) EC2SYS-48:60"x60"x66"(1524mmx1524mmx1676mm) ELECTRICALVOLTAGEPHASECYCLE/HZAMPSkW120/208-240(UL)150/6013.83.3at208150/6011.62.5at240150/6

4. Do not touch surfaces that may be hot. Always use hot pads or potholders until the appliance is cooled. 5. Before using for the first time, check if voltage indicated on the base of the appliance corresponds to the voltage in your home. 6. Do not turn on the power unless this appliance is properly assembled. 7. Do not operate this appliance with a damaged cord or plug, or after the appliance malfunctions, or has been damaged in any manner. Return it to the nearest authorized service facility

Press and hold the on/off key until the LED display turns off (at least three seconds) and on/off indicator goes out. UP/DOWN ARROW KEY The up and down arrow keys are used for a variety of settings when selecting the holding temperature. If an arrow key is pressed and released the display will show the current set temperature for two seconds. If an arrow key is held (at least eight seconds), the value will change at a rapid rate. If the arrow key is pressed and released in rapid succession, the

Donotinstallaheateddisplaycasenearacoldairsourcesuchasafreezer,airconditioningvents,orinanyareawhereoutsideairfluctuationcanaffectperformance. ELECTRICAL CORD 96" (2438mm) CUTTING BOARD IN “DOWN” POSITION CUTTING BOARD IN “DOWN” POSITION 6-3/4" (172mm) ON OFF ON OFF ON OFF52- 3/ 16" ( 1325mm) WEIGHTMODELNETSHIPTY2-96501lb(227kg)610lb(277kg) TY2SYS-96735lb(333kg)1005lb(456kg) TY2-96/PL;/PR575lb(260kg)685lb(311(kg) TY2SYS-96/PL;/PR810lb(367kg)1005lb(456kg) CRATEDDIMENSIONS(EST.):HXWXDTY2-96:45"x10

For fully enclosed sections, resetthe thermostat to the number “8” setting. Cases with a self-service section should be maintained between number “9” and number “10” for the self-service section only. THESE SETTINGS WILL NOT NECESSARILY BE FINAL. Since propertemperature range depends on the type ofproducts and the quantities being held, it isnecessary to periodically use a pocketthermometer to check each item to make certain the correct temperatures are being maintained. Proper temperature range

#78A -03/08 EC2-72 EC2SYS-72 EC2-72 SERIES OPTIONS&ACCESSORIES BUTTINGKITCONTACTFACTORY GAUGE,INTERIORAMBIENTTEMP.GU-33384 GLASS,NON-GLARE,FRONTGL-26695 GLASS,TEMPEREDENDPANE,BRONZEKIT5008528 INDEPENDENTELECTRICALOUTLET5001781PANELKIT,COUNTERTOP BRUSHEDSTAINLESSSTEEL5004695 CUSTOMCOLOR5004701PANELKIT,SYSTEM BRUSHEDSTAINLESSSTEEL5004698 CUSTOMCOLOR5004704 PANINSERT,SELF-SERVICE4"(102mm)DEEP1001991 PLATFORMSCALE55265SHEETPANDIVIDERBARPACKAGE FULL-SERVICE&SELF-SERVICEFULLCASES5002803 SELF-SERVICELE

The terminal is marked with the following symbol. HN2 & HN2SYS Series Operation & Care Manual • 5 INSTALLATIONINSTALLATION HN2 & HN2SYS SERIES OPTIONS & ACCESSORIES DESCRIPTION HN2-48 SERIES HN2-72 SERIES HN2-96 SERIES BUTTING KIT AVAILABLE AVAILABLE AVAILABLE GAUGE, INTERIOR AMBIENT TEMPERATURE GU-33384 GU-33384 GU-33384 GLASS, TEMPERED END PANE, BRONZE KIT 5008529 5008529 5008529 INDEPENDENT ELECTRICAL OUTLET 5001781 5001781 5001781 PANEL KIT, COUNTER TOP BRUSHED STAINLESS STEEL CUSTOM COLOR 5

FLEXIBLE WATER- TIGHT TETHERDECOR FACE SCREWS 1. 100-HW, 200-HW or 300-HW: Cut a 5-1/4" x 4-1/2" (133mm x 114mm) opening in the location where the control is to be positioned. 400-HW or 500-HW: Cut a 9-1/8" x 4-1/2" (232mm x 114mm) opening in the location where the control is to be positioned. 2. Thoroughly clean and dry the mounting surface around the control cut-out opening on which the decor face will be applied. NOTE: The control face will not properly adhere to an unclean surface. 3. Remove

The base is divided into two (2) individually managed heat zones with each zone controlled by a separate thermostat with a range of 1 through 10 and heat-on indicator light. Overhead lights are controlled by ON/OFFswitches in two (2) light zones. Two (2) 125V plug outlets are available as an option on 120/208-240V units only. ¦ PD2SYS-48 -48" (1219mm) length FACTORY INSTALLED OPTIONS . Panel Color Choices Specify color choice: ANSI/NSF 4 ¦ Black, standard ¦ Stainless Steel, optional ¦ Custom Col