Évaluations - , GPA: ( )

Instructions Invacare, Modèle 3700

Fabricant : Invacare
Taille : 158.96 kb
Nom Fichier :

Langue d'enseignement:

Le document est chargé, s'il vous plaît patienter

Téléchargez votre Fermer

Le document est chargé, s'il vous plaît patienter

Téléchargez votre Fermer

NEVER use cleaners containing iodine, bromine, Betadine® or methylene blue. The use of these types of cleaners will cause the tub to stain. Never use cleaners containing bleach. Use of these types of cleaners will dry out the rubber seals and gaskets and the tub will not function properly. Before starting the whirlpool pump, the water level must be completely above the whirlpool jets. Otherwise damage to the motor/pump will result. Heavy Duty Cleaning Procedure In additionto disinfecting yourtubafter every use, youwill need to performthis procedureapproximately once every 80.150 baths. 1. Clean the entire surface of the tub to remove visible tissue residue and fluid. 2. Rinse the inside surface of the tub with the shower/massage wand on the spray setting. 3. Rotate the water temperature valve to adjust the water temperature to approximately 105o F. NOTE: This will maximize the cleaning solution.s ability to clean and disinfect the system. 4. Close the drain. 5. Make sure the whirlpool jets are open. 6. Fill the tub one inch above the highest whirlpool jets. 7. Add the Invacare Heavy Duty Cleaner to the water in the tub. Refer to the chart for the proper amount. 8. Spray pre.mixed Invacare Heavy Duty Cleaner on the remaining surfaces. 9. Press the whirlpool on/off button to turn on the whirlpool pump and let the pump runfor 60 seconds. 10. Turnoffthepumpandallowtheheavydutycleaner/watersolutiontoremaininthetubfor 10 minutes. 11. During this ten.minute waiting time, take a long handled brush and thoroughly scruball interior surfaces of the tub. 12. Open the drain to allow the heavy duty/water solution to drain from the tub. 13. Use the shower/massage wand on the pulse setting and direct the spray into bothwhirlpool jets to back flush until the water discharging from the whirlpool inlet is clear. 14. Rinse the tub thoroughly with the shower wand on the spray setting. 15. Check the tub for damage and to ensure all surfaces of the tub are clean and that novisible residue remains. If residue is found, repeat STEPS 13 and 14. TUB MODEL NUMBER WATER REQUIRED TO COVER JETS (GALLONS) INVACARE HEAVY DUTY CLEANER REQUIRED (OZ)* 2800 10 40 2001 32 128 3700 30 120 3750 30 120 3800 30 120 3600 30 120 3650 48 192 3600XL 48 192 2300 25 100 3300 30 120 4300 35 140 4300HL 35 140 5300 52 208 5300HL 52 208 6300 50 200 6300ADH 50 200 4400SS 48 192 5400SS 50 200 *NOTE: If using non.Invacare heavy duty cleaner, refer to the instructions supplied with the cleaner to determine the proper amount required. Invacare Continuing Care Group USA Canada One Invacare Way 994 Hargrieve Rd. All rights reserved. Trademarks are identified by the symbols ™ and ®. All Elyria, Ohio USA London Ontario trademarks are owned by or licensed to Invacare Corporation unless 44036-2125 N6E IP5 Canada otherwise noted. Betadine is a registered trademark of Purdue Pharma L.P. © 2008 Invacare Corporation Part No 1154271 For customer service call: 800-668-2337 Rev A - 04/08 ...