|
Par ce dispositif a également d'autres instructions :
Facilité d'utilisation
To use an iPod, refer to the user’s guide of your iPod. Notes . When inserting an iPod into the unit, be sure to use the universal dock adapter supplied with your iPod or commercially available from Apple Inc. . If you are using an iPhone or iPhone 3G, attach the supplied universal dock adapter for iPhone or iPhone 3G before inserting into the connector. The adapter number, . or ., is shown on the bottom-rear of the supplied Universal Dock Adapters. . is for the iPhone, and . is for the iPhone 3G. Check the adapter number before use. . The connector of the unit is exclusively for use with iPod. When you use a device that does not match the connector, connect it to the AUDIO IN terminal of this unit with the supplied audio connecting cable. . Sony cannot accept responsibility in the event that data recorded on an iPod is lost or damaged when using an iPod connected to this unit. . For details of environmental conditions for operating your iPod, check the website of Apple Inc. 1 Push the iPod lid to open the iPod connector. 2 Attach the correct universal dock adapter to the connector of the unit, and place the iPod/iPhone to the connector. 3 Press iPod & iPhone .. The iPod begins to play automatically. You can operate the connected iPod by this unit or the iPod buttons. 4 Adjust the volume using VOLUME + or –. To Press Turn off the iPod OFF, or press and hold iPod & iPhone . Pause playback iPod & iPhone . To resume play, press it again. Go to the next track . Go back to the previous track .* To Press Locate a point while listening to the sound . (forward) or . (backward) while playing and hold it until you find the point. Locate a point while observing the display . (forward) or . (backward) in pause and hold it until you find the point. Go back to the previous menu MENU** Select a menu item or a track for playback ./.** Execute the selected menu or begin playback ENTER** * During playback, this operation goes back to the beginning of the current track. To go back to the previous track, press twice. ** These operations are available only when using the supplied remote commander. Notes . When placing or removing the iPod, hold the iPod at the same angle as that of the connector on this unit and do not twist or bend the iPod to prevent connector damage. . Do not carry the unit with an iPod set on the connector. Doing so may cause a malfunction. . When placing or removing the iPod, brace the unit with one hand and take care not to press the controls of the iPod by mistake. . Before disconnecting the iPod, pause playback. To use the unit as a battery charger You can use the unit as a battery charger. The charging begins when the iPod is placed on the connector. The charging status appears in the iPod display. For details, see the user’s guide of your iPod. On copyrights . iPod is a trademark of Apple Inc., registered in the U.S. and other countries. . iPhone is trademark of Apple Inc. . All other trademarks and registered trademarks are of their respective holders. In this manual, ™ and ® marks are not specified. Setting the alarm This CD clock radio is equipped with 4 alarm modes—CD, iPod, radio and buzzer. Before setting the alarm, make sure to set the clock (see “Setting the clock for the first time”). To Set the alarm 1 Press and hold ALARM TIME SET A or B for at least 2 seconds. “WAKE UP” appears and the hour flashes in display. 2 Press ALARM TIME SET + or – repeatedly until the desired hour appears. To set the hour rapidly, hold down ALARM TIME SET + or –. 3 Press ALARM TIME SET A or B. The minute flashes. 4 Repeat step 2 to set the minute. 5 Press ALARM TIME SET A or B. The days of the week blink. 6 Repeat step 2 to set the days of the week. You can select the days from the following three options: Every day: SUN MON TUE WED THU FRI SAT Week day: MON TUE WED THU FRI Week end: SUN SAT 7 Press ALARM TIME SET A or B. The alarm mode setting is entered. 8 Press ALARM TIME SET + or – repeatedly until the desired alarm mode flashes. You can choose one mode among “CD”, “iPod”, “RADIO” and “BUZZER”. Set the alarm mode as follows: – CD: see “. Setting the CD alarm”. – iPod: see “. Setting the iPod alarm”. – RADIO: see “. Setting the radio alarm”. – BUZZER: see “. Setting the buzzer alarm”. . Setting the CD alarm For the CD alarm, the track you specified as the wake-up track is played first. (If the CD play mode is set to “SHUFFLE” or “SHUFFLE REP”, all the tracks will be played in random order.) 1 Perform steps 1 to 8 in “To set the alarm”. 2 Press ALARM TIME SET A or B to select “CD” alarm mode. “VOL” and “TRCK” appear in the display. 3 Press ALARM TIME SET + or – to adjust the volume. 4 Press ALARM TIME SET A or B. Track number flashes. 5 Press ALARM TIME SET + or – to select the desired track number. 6 Press ALARM TIME SET A or B. The setting is entered. When “A” or “B” does not appear in the display, press ALARM TIME SET A or B again. The CD will play at the set time. Note If the CD alarm does not operate becaus...