Évaluations - 0, GPA: 0
(
)
)
|
Par ce dispositif a également d'autres instructions :
Facilité d'utilisation
Problems fixed in recent releases
SR number
Description
QXCR1001311463 LAN connectivity failure when using HPVM Guest based VLANs
LAN connectivity failure when using HPVM Guest Based VLANs (GBV) over a vswitch backed by a
LAN interface, if there is no VLAN configured on LAN interface on VSP.
QXCR1001292744 Install script overwrites the entry in nettlgen.conf unconditionally
When updating the product, the corresponding nettlgen.conf entry goes back to the default setting.
QXCR1001293922 Invalid speed reported for APA: LAN Monitor port on Flex10 interfaces
When the two LAN interfaces connected to Virtual Connect Flex10 are configured in a LAN Monitor
group, and both interfaces have a speed set to 5 Gig, the APA LM port reports speed as 10 Gigabit
instead of 5 Gig.
QXCR1001299480 VPD (Serial Number) information is not updated with olrad -R/-r command
When the command olrad -d /olrad -A is used, and a new network adaptor is physically added,
the VPD information is updated properly, but When the command olrad -r /olrad -R is use, and
network adaptor is physically added, the VPD information (Serial number) is NOT updated.
QXCR1001281632 ER: Port initialization failed with "4.2.401.2212" Firmware
When “Advanced Mode” is enabled as shown from UEFI configuration tool and LAN driver is loaded,
it fails to claim the card with following DISASTER error:
iocxgbe19: INITIALIZING HP NC553m 2p 10GbE BL-c
Mezzanine Adapter at hardware path 0/0/0/5/0/0/3
DISASTER: instance number(ppa): 1
The Emulex CNA can operate in both Legacy and Advance modes. For Factory Fresh installs, the
firmware versions 4.2.x.x onwards will program CNA in Advance mode by default. For Firmware
upgrades to existing systems, the current mode setting for CNA will be preserved. The LAN driver
currently supports the Emulex CNA in legacy mode only. The mode-change requires an adaptor reboot
to take effect. So, the compatibility changes are made in the driver in such a way that it can work with
CNA in both legacy mode as well as in Advance mode.
QXCR1001269384 ER: Speed up driver boot time
The boot time configuration delay when multiple parameters are being set is now reduced significantly.
Prior to this release, system boot time could be impacted significantly by the number of parameters
being set in the configuration file, especially in system configurations supporting a large number of
LAN interfaces. Each configuration parameter was set using independent calls to the driver. Additional
delays would result if driver resets were required for the settings to take effect. With this release of the
driver, a single call is used to set multiple parameters, reducing the delay caused by multiple resets.
A new command line option has been added to the lanadmin command to provide this enhancement:
lanadmin -X boot_param [{send_cko_on | send_cko_off}] [vmtu={0 | 32160}] [{recv_cko_on| recv_cko_off}]
[{drv_pr_off | drv_pr_on}] [mtu=<size>] [tx_coal=<0-1000000>] [rx_coal=<0-1000000>] <ppa no>
For example:
lanadmin -X boot_param vmtu=0 send_cko_off recv_cko_off tx_coal=0 rx_coal=0 drv_pr_off mtu=9000 6
SR number
Description
QXCR1001246487 olrad -r/R command does not flag and block attempts to replace an adapter with a different type of
adapter
When replacing an interface adapter online, an identical adapter must be used as the replacement.
The iocxgbe driver should detect and block mismatches but was failing to do so. All replacements were
treated as if identical, causing unpredictable results. The driver now detects and blocks attempts to
replace an adapter with one that is not identical.
QXCR1001231153 Host panic on fault when executing in kernel mode during reboot of vPars
During reboot of vPars, the host crashes while freeing MSI objects. A message like the following is
displayed in msgbuf immediately prior to the crash:
10
... Ce manuel est également adapté pour les modèles :
Matériel de réseau - HP-UX 11i v3 I/O Cards (290.31 kb)