TO REMOVE GUARD: Open guard release/lock latch, rotate guard until the two bumps on guard line up with the two notches on the spindle neck, and lift guard off the spindle neck. Assembly -7- LOCK NUT AND BACKING FLANGE Your tool is equipped with a threaded spindle for mounting accessories. Always use the supplied lock nut (and backing flange) that has same thread size as spindle. SIDE HANDLE The side handle used to guide and balance the tool can be threaded into the front housing on either side o

Do not start the tool on the workpiece. Always run the tool for at least one minute before operation. This allows the tool to reach full speed. ! CAUTION RELEASE TABS VARIABLE SPEED DIAL (Model 1295DVS only) BM 2610914126 9-03 10/1/03 10:31 AM Page 6 BM 2610914126 9-03 10/1/03 10:31 AM Page 7 Operating Instructions ROCKER “ON/OFF” SWITCH (Models 1295D, 1295DP, & 1295DVS) TO TURN THE TOOL "ON" depress the upper portion of the dust-protected switch to the number “1” position. TO TURN THE TOOL "OFF

This should be done both phase-to-phase and phase-to-ground. 7. MOTOR OVERLOAD PROTECTION: The pump motor is protected from locked rotor and running overloads by a thermal overload integrally mounted to the motor. No adjustments are required. Check to determine that all grounding connections are made properly 8. If a panel is used, remove all debris, scrap wire, etc., from the control panel interior before closing the doors. Install covers, close doors making certain that no wires are pinched an

2 Gang Socket FROM ONLY 63pSee Page 2 order code PL0921508 GET FAST, FREE DELIVERY!* GET REAL TRADE PRICES! SPRING/SUMMER 2008 Offers End 30th September 2008 + FreeDiamondBlade andCase All Prices Exclude VAT GET EVERYTHING UNDER ONE ROOF! ONLY .29.95 order code TL1207108 See Page 133 Electrical Cables & Connectors Aerials & Satellite PA/AVInstallation Computers & Networking Lamps Lighting Security Batteries Heating & Ventilation Workwear Health & Safety Labelling Sealants & Adhesives Cleaning &

The closed side of the protection guard 6 must always point to the operator. Auxiliary Handle For all work with the machine, the auxiliary handle must be mounted. Screw the auxiliary handle 3 on the right or left of the machine head depending on the working method. Hand Guard For work with the rubber sanding plate 13 or with the cup brush 16/disc brush/flap disc, the hand guard 12 (accessory) is to be mounted. The hand guard 12 is fastened with the auxiliary handle 3. Before any work on the ma

Wear protective gloves and eye protection when using compressed air. NOTE: Do not wash the canister with soap and water. Dust may become more firmly lodged in the pores, which will reduce dust collection. Your sander was designed to sand in small or confined areas. Its small size and light weight makes it ideal for overhead work. The dust canister rotates 360° for operator comfort and work visibility. You may grip the tool on top or around the motor housing as shown, which was contoured for that

Any alteration or modification is a misuse and may result in a dangerous condition. Check for misalignment or binding of moving parts, breakage of parts, and any other condition that may affect the tools operation. If damaged, have the tool serviced before using. Many accidents are caused by poorly maintained tools. Develop a periodic maintenance schedule for your tool. Use only accessories that are recommended by the manufacturer for your model. Accessories that may be suitable for one tool, ma

We recommend that all tool service be performed by a Bosch Factory Service Center or Authorized Bosch Service Station. TOOL LUBRICATION Your Bosch tool has been properly lubricated and is ready to use. It is recommended that tools with gears be regreased with a special gear lubricant at every brush change. CARBON BRUSHES The brushes and commutator in your tool have been engineered for many hours of dependable service. To maintain peak efficiency of the motor, we recommend every two to six months

Align locating bumps on damper ring with cut outs in shroud and depress ring with thumbs until shroud seats into groove completely around ring, then tighten screws. IMPORTANT: Ring should not have bends or ripples when correctly seated. Apply a thin film of light grease to top side of backing pad where the damper ring makes contact, reassemble backing pad and firmly tighten screw. BACKING PAD DAMPER RING SHROUD LOCATING BUMPS ON UNDERSIDE OF DAMPER RING INSTALLING ACCESSORIES (Model 1295D 1295DH

Speed Preselection (GWS 6-100 E, GWS 6-115 E, GWS 8-100 CE, GWS 8-115 CE, GWS 8-125 CE) Preselect the required speed using the thumb wheel 1 according to the table following the section “Tool Specifications” (reference values). Operating Instructions Clamp the workpiece if it does not remain stationary due to its own weight. Do not strain the machine so heavily that it comes to a standstill. Grinding and cutting discs become very hot while working; do not touch until they have cooled. Rough G