P1582 07/98 WARRANTY REGISTRATION AND POLICY Buhler Manufacturing products are warranted for a period of twelve (12) months from original date of purchase, by original purchaser, to be free from defects in material and workmanship under correct, normal agricultural use and proper applications. Buhler Manufacturing's obligations under this warranty shall be limited to the repair or exchange, at Buhler Manufacturing’s option, of any Buhler Manufacturing product or part which proves to be defec

Torque to 500 ft-lbs. IMPORTANT: When mounting for the first time, the front hook bolts will have to be tightened after positioning the hook directly over the mounting boss (most rearward position). 9. Raise the loader and lock the support stand tubes into the up position. NOTE: When mounting for the first time, raise the loader slowly and check to make sure that the hoses do not bind or become pinched in all positions. Work the loader and bucket up and down to work out all the air in the hyd

. 2. Move and turn tractor at low speed. 3. Carry loader arms at a low position during transport. ■ 4. Lower loader arms, stop engine and lock brakes before leaving operator seat. 5. Do not stand or work under raised loader, unless properly ' supported. 6. Add recommended wheel ballast or rear weight for stability. 7. Move wheels to widest recommended settings to increase stability. 8. Do not handle large round bales or other shiftable objects unless loader is equipped with a grapple fork

Use the valve type shown with hose Kit "B”. HOSE KIT "C" Loader operated by an external valve "3" that is plumbed into the tractor hydraulic system. Consists of four hoses "I" leading from loader tubing "2” to the external mounted valve "3" plus the necessary fittings, hoses and adapter blocks (if necessary) to tap into tractor hydraulic system. Use valve type shown with hose Kit "C". /K IMPORTANT PRECAUTIONS A DANGER Æ ELECTROCUTION HAZARD To prevent serious injury or death: • Stay

Loose connections. Worn or damaged O-ring wiper seal in cylinder rod end. Worn or damaged O-rings in valve. Replace damaged parts. Tighten fittings. Install a seal repair kit. Install an O-ring repair kit. Insufficient lift capacity Improper hydraulic pump operation. Repair or replace pump. Load is greater than boom lift capacity. Check loader specifications. Internal boom cylinder leakage. Replace any worn parts and install a seal repair kit. Improper hydraulic valve operation. Repair or repla

x 20.75 Cyl. Assy. Bucket 24314 3.0 Dia. x 30.00 Cyl. Assy. Lift 811572_3/8 x 15" Hose 3/4 MORB x 3/4 SWFJIC 811471 3/8 x 20" Hose 3/4 MORB x 3/4 SWFJIC 811466 3/8 x 24" Hose 3/4 MORB x 3/4 SWFJIC 812947_3/8 x 22" Hose 3/4 SWFJIC x 3/4 SWFJIC 112833 Tubing - Lift Cyl. Bottom Raise 112834 Tubing - Lift Cyl. Top Drop 112937 Tubing - Lift Cyl. Common (31.0") 112835 Tubing - Bucket Cyl. Bottom Rollbk 112836 Tubing - Bucket Cyl. Top Dump 112837 Tubing - Bucket Cyl. Cross Tube 812128 Elbow 90

x 20.75 Cyl. Assy. Bucket 24314 3.0 Dia. x 30.00 Cyl. Assy. Lift 811572_3/8 x 15" Hose 3/4 MORB x 3/4 SWFJIC 811471 3/8 x 20" Hose 3/4 MORB x 3/4 SWFJIC 811466 3/8 x 24" Hose 3/4 MORB x 3/4 SWFJIC 812947_3/8 x 22" Hose 3/4 SWFJIC x 3/4 SWFJIC 112833 Tubing - Lift Cyl. Bottom Raise 112834 Tubing - Lift Cyl. Top Drop 112937 Tubing - Lift Cyl. Common (31.0") 112835 Tubing - Bucket Cyl. Bottom Rollbk 112836 Tubing - Bucket Cyl. Top Dump 112837 Tubing - Bucket Cyl. Cross Tube 812128 Elbow 90

If the loader is lowered from this position, the bucket will extend as the quick attach contacts the rollback stop and the circuit goes through relief as described in note 2. The relief valve is factory set at 3250 PSI cracking pressure and is capable of bypassing 10-15 GPM. If loader lock-up should occur due to a low tractor relief setting, higher inlet flows or return line restrictions, the relief valve may be backed off slightly until the lock-up condition is overcome (counterclockwise turn

Any sample or model is for illustrative purposes only and does not create an Express Warranty that the goods conform to sample or model shown. t The purchaser is solely responsible for determining suitability of goods sold. This warranty is expressly in lieu of all other warranties expressed or implied. Buhler Manufacturing will in no event be liable for any incidental or consequential damages whatsoever, nor for any sum in excess of the price received for the goods for which liability is clai

Hoses should be connected in such a manner that pushing forward on valve handles lowers the boom or dumps the bucket. CAUTION: Always connect boom hoses to float section. Weight added to rear of tractor provides better traction and an easier, more efficient loader operation. Extra weight, along with widening the rear wheels, reduces the risk of roll-over. /f\ I WARNING I The smaller the tractor is, the easier it will roll. We recommend that weight be added to rear tires with liquid or by the