After the battery is charged, reconnect the positive battery cable first and the negative cable last. Failure to do so can result in damage to the internal charger components. Follow the instructions of the battery charger manufacturer for proper charger settings and charging time. SERVICING MUFFLER WITH INTERNAL SPARK ARRESTOR Clean every 100 hours. Remove screw plug on muffler body and either vacuum out OR shake out until clean. WARNING • MUFFLER MAY bE HOT • ALLOW ENGINE TO COOL bEFORE INSTAL

When set on Max., the electrode feeds at more than 500” per minute and the welding current is high. If the power source is equipped with meters, the welding current can be read directly on the ammeter while welding. If the power source has no meters and the relationship between current and wire feed speed is known, current can be accurately set by measuring the wire feed speed. To measure wire feed speed disconnect the electrode cable at the power source: 1. Press the gun trigger and feed ele

Specifications and availability of optional features may have changed. Shipping Damage Claims When this equipment is shipped, title passes to the purchaser upon receipt by the carrier. Consequently, claims for material damaged in shipment must be made by the purchaser against the transportation company at the time the shipment is received. Safety Depends On You Lincoln arc welding equipment is designed and built with safety in mind. However, your overall safety can be increased by proper ins

Specifications and availability of optional features may have changed. 5? /SÄB8î ■ ■ < ^ >.. i. -,?è. y . - . ■ ... • • : THE LINCOLN. ELECTRIC‘ £[ ELECTRIC {Worlds Largest Manufacturer of Arc*Welding Equipment and Electrodes ■> Manufacturer of Motors Since 1895 " ...........................Cleveland, Ohio 4411T U.S.A. : •• Paditow; N. S. W.( Australia • ' '%№W%^Sêÿîk........... T a ronto, Oretia-r ! o,' Canad a G r a n d - Q u e v i 11 y, 76—Franc» INSTALLATION DAMAGE CLAIMS When thi

. . and thoughtful operation on your part. DO NOT INSTALL, OPERATE OR REPAIR THIS EQUIPMENT WITHOUT READING THIS MANUAL AND THE SAFETY PRECAUTIONS CONTAINED THROUGHOUT. Most importantly, think before you act and be careful. OPERATOR’S MANUAL Copyright© 2004 Lincoln Global Inc. • World’s Leader in Welding and Cutting Products • • Sales and Service through Subsidiaries and Distributors Worldwide • Cleveland, Ohio 44117-1199 USA Tel: 216.481.8100 Fax: 216.486.1751 Web Site: i SAFETY i WARNING CALIF

Slide the guide tube up against the installed drive roll. 9. Install the second drive roll on the remaining shaft the same way as the first. Center the middle guide tube between the rolls and tighten the thumbscrews holding it in place. 10. Close and latch both quick release levers. 11. Slide the longer guide tube into the rear hole of the gearbox until it almost touches the drive roll and guide tube. Tighten the thumbscrew to hold it in place. 12. Install the outgoing guide tube into the front

. . . . . . . . . . . . . . . . B-8 Making a Weld . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-12 Wire Reel Changing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-12 Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Section C General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-1 Flux System C

Features: • Easy Installation • Input power cable and plug included Easy to Operate • Electrode holder and cable, work clamp and cable, sample electrodes, welding helmet and welder's guidebook all included • Easy to use controls •Convenient size to allow easy storage and handling • 3 year warranty including parts and labor • Output: 170 amps, 25 volts, 20% duty cycle • Amp Range: 40-225 • Size: 15.2”h X 14”w X 13.5”d • Weight: 86 lbs. • CSA approved • UL listed • Powder Paint Finish for increase

Handles flux-cored welds on mild steel with ease. Practically everything you need to MIG weld mild steel is right in the box. Unit includes: • 4-Step Tap voltage control • Magnum® 100L welding gun and 10ft. (3m) cable assembly, with gas nozzle, .023” - .035” (0.6–0.9mm) cable liner and .023/.025” (0.6mm) contact tip • 10ft. work cable & work clamp • 6 ft input power cord with NEMA Type 5-15P plug • Guide tubes and reversible drive roll for .023-.035" solid MIG wire and .035" Innershield® flux-co

• 3 year warranty including parts and labor • Output: AC: 225 amps, 25 volts, 20% duty cycle • DC: 125 amps, 25 volts, 20% duty cycle • Amperage range: AC 40-225, DC 30-125 • Size: 24”h X 17.3”w X 12”d • Wt: 129 lbs. P/N 12-00774 ........$467.95 Wheel Kit ................................P/N 12-00775 ..........$10.60 LINCOLN WELDERS LINCOLN POWER MIG 140T & MIG 140C Select the economical Power MIG® 140T (K2470-1)with simple tapped voltage control for basic MIG and flux-cored welding. Choose the P