Read all instructions carefully. 2. Use iron only for its intended use. 3. To protect against risk of electrical shock, do not immerse the iron in water or other liquids. 4. Never yank cord to disconnect fromoutlet. Grasp plug and pull to disconnect. 5. Do not allow cord to touch hot surfaces. Let iron cool completely before putting away. 6. Always disconnect iron from electricaloutlet when filling with water, emptying, or when not in use. 7. Do not operate iron with a damaged cord, or after the

To fully enjoy the advantages of your appliance, please take a few minutes to read all the “ Use & Care Instructions” andkeep the instructions handy for easy reference. Please review the product warranty and mail the owner registration form. Model GI460 Printed in China 10 IMPORTANT SAFEGUARDS When using your garment steamer/iron, basic safety precautions should always be followed, including the following: 1. Read all instructions carefully. 2. Use garment steamer/iron only for its intended use.

( Fig. 8) To reset your iron and continue ironing follow these steps. 1) Lift iron from ironing board. 2) Holding the iron horizontally in front of you, gently rock the iron back and forth several times. This motion will reset the safety switch inside the iron. DO NOT shake the iron. The ambertemperature ready light will illuminate when the auto shut-off system has been reset. Allow time for the iron to re-heat. The amber temperature indicator light will go out when the iron is ready for use. Fi

ANTI-DRIP FEATURE Built-in Anti- Drip feature helps reduce water spots by cutting the water flow when the iron temperature is too low to build sufficient steam. The anti-drip function reduces water dripping and water stains. It does not prevent water dripping and water stains if you press the steam burst button too often or if the temperature is too low. The amount of water droplets will eventually decrease after the iron is used for 2 to 3tankfulsof steaming and ironing. Fig. 9 Fig. 2 All marke

• Water tank may be empty or water level is very low. Add water. • Make sure that the fabric/temperature setting and the variable steam control are correctly set. For maximum steam, (setting ‘Max’ on steam control), temperature setting should be set on ‘• •• ’. • Variable steam control dial is set on “0”. Always allow the iron to reach the selected temperature with the variable steam control setting at ‘0’. Make sure the temperature setting is set in the correct steam area, e.g. ‘•’, and the ste

1 Open the water inlet cover located on the front of the iron. 2 Holding the iron at a slight angle; fill the tank with the filling flask without going over the “MAX” line. Close the water inlet cover. 3 Plug in the iron. 4 Choose dry or steam ironing based on the type of fabric you are going to iron. For DRY ironing set the steam control dial to “0”. For STEAM ironing set to desired steam for the type of material to be ironed. 5 Set the desired fabric/temperature by pressing the Electronic Temp

Iron should be plugged into a 120V AC electric outlet only. Make sure the plug is securely in the socket. Temperature setting might be too low. Try turning to a higher setting. Water droplets coming from steam vents. Variable Steam Control Dial may be set in “self clean” position. Align the dial to the "0" to "Max" steam setting. Iron may not be hot enough. Set temperature to “MAX” position. Always allow iron sufficient time to heat up before activating the variable steam control. Overuse the st

STEAM IRONING1 Open the water filling inlet cover. Holding the iron at a slight angle, pour the water slowly into the inlet. The soleplate design allows for ordinary tap water to be used. We recommend using the mix of 50% tap water and 50% distilled water to reduce the hardness. 2 Using the filling flask, fill the tank to a desired level without going over the “MAX” line on the water tank. 3 When you’re finished, close the inlet cover before continuing. 4 Plug the cord into a polarized 120V AC e

Be careful, burns or serious injury may occur. CAUTION: Never iron or steam clothes while they are being worn. If the tank runs dry, always make sure you unplug the iron from the outlet before you refill. Self-CleaningSelecting suggest that you self-clean the iron at least once every two weeks to remove scale and calcium. If you know you have very hard water we recommend that you self-clean the iron more often. 1 Set the steam control lever to any steam position. 2 Fill the water tank up to the

6. Set variable steam control to " 0". 7. Allow iron to cool in an upright position before storing. WARNING! Use caution when emptying the iron. Burns may occur from touching hot metal surfaces, hot water or steam. STORAGE1. Always turn the variable steam control to “0” after you have emptied the water tank. 2. Allow the iron to cool down. 3. Always store the iron in the upright position to protect the soleplate. 4. From time to time, clean the exterior of the iron with a damp cloth and wipe dry