Évaluations - 1, GPA: 5
(
)
)
|
Facilité d'utilisation
120 mm dia. for two-motor hoods). Failure to observe these principles is inevitably associated with power losses and increased operating noise. During installation of the fume extractor hood, the following minimum distances from the upper edge of the hob to the lower edge of the fume extractor hood must be complied with: Electric cookers 650 mm Gas cookers 650 mm Coal- and oil-fired cookers min. 700 mm For the kitchen furniture installer General Appliance description The fume extractor hood is supplied as an exhaust air appliance and may be used as a return air appliance through application of an active carbon filtre (special accessory). For this purpose, you need the AEG Original Active Carbon Filter (see special accessories). A = Light switch B = Blower switch (On/Off) C = Blower switch settings D = Metal filter grille (fat filter) The fume extractor hood is switched on and controlled via the different controls Technical data Dimensions: 860 D Height Width Depth (in mm) 255 599 490 Weight: Net: 22 kg 8609 D Height 255 Width 899 Depth 497 (in mm) Weight: Net: 24.5 kg AL1 11/89 - GBM3 5/90 - TDM1A 5/90 GB/EU TDM2B 5/90 - TDM3A 5/90 - LAD3 5/90 GB/EU Connection value: 860 D 8609 D Total connected load: 179 W 180 W Fan motor: 2 x 82 W 2 x 82 W Lighting: 1x 15 W 1x 16 W {fluorescent lamp) (fl. lamp) Fan outputs (settings) to DIN 44 971 860/8609 D Setting 1 Setting 2 Setting 3 Setting 4 Exhaust air: 200 m3/h 320 m3/h 400 m3/h 520 m3/h Return air: 140 m3/h 240 m3/h 290 m3/h 360 m3/h Exhaust air system 125 mm dia. Air outlet arranged centrally above Pipe connection of 125 mm dia. for exhaust air hoses of 125 mm dia. Air outlet Draufsicht = Plan 31 Accessories/installation materials Preparing for exhaust air operation 1 wall rail (for mounting of fume extractor hood) 4 wall plugs for 8 mm, 40 mm long wood screws (for mounting of chimney retaining plate on wall and wall rail) 4 button-head wood screws, 5 x 40 to DIN 7996 2 wall plugs for 5 mm, 30 mm long wood screws (for mounting of clamping piece) 2 button-head wood screws, 6 x 30 to DIN 85 1 drilling template for appliance mounting 1 125 mm dia., 800 mm long hose 2 125 mm dia. hose clips for above 1 chimney equalizer (230 mm high) 1 chimney cover plate with air outlet grille for return air 1 chimney retaining plate 1 guide piece (T-piece) for return air operation 4 button-head 2.9 mm x 6.5 mm long sheet metal screws (for mounting of chimney retaining plate with chimney cover plate) 3 5x 60 mm screws to DIN 7996 for mounting of wall rail 3 8 x 60 mm wall plugs for wall rail The fume extractor hood is factory-supplied for commissioning in upward exhaust air mode. Prior to installation of the fume extractor hood, a hole should be arranged in the outer wall for the wall box (return/supply air) apart from mounting drillholes. ZM3 5/90 - VOA2 5/90 GB/EU VMA1 11/89 - LAÖ2 5/90 GB/EU If the kitchen fume is run out into the open air through the e...
Ce manuel est également adapté pour les modèles :Ventilateurs - 860 D (574.54 kb)
Ventilateurs - 860 D (574.54 kb)
Ventilateurs - 8609 D (574.54 kb)
Ventilateurs - 8609 D (574.54 kb)