(‘'Coleman") warrants that for a period of one (1) year from the date of purchase, this product will be free from defects in material and workmanship. Coleman, at its option, will repair or replace this product or any component of the product found to be defective during the warranty period. Replacement will be made with a new or remanufactured product or component. It the product is no longer available, replacement may be made with a similar product of equal or greater value. No warranty is pro

CF2650BC01 CF2650WB01 CF2650PW01 RAPHAEL™ / RAPHAEL II™ ® Net Weight: 29.5 Lbs. Ceiling Fan Owner's Manual LIMITED WARRANTY What The Warranty Covers: This warranty covers the motor and the other components and accessories of your Emerson ceiling fan against all defects in workmanship and materials. You must be the original purchaser or user of the product to be covered. What The Period Of Coverage Is: As it applies to the motor, this warranty will last for a lifetime from the date you purchased

Carefully lift the fan and seat the hanger ball/downrod assembly on the hanger bracket that was just attached to the outlet box (Figure 19). Be sure the groove in the ball is lined up with the tab on the hanger bracket (Figure 18). Failure to seat tab in groove could cause damage to electrical wires and possible shock or fire hazard. WARNING ! NOTE: CEILING COVER, SUPPLY WIRES AND FAN WIRES OMITTED FOR CLARITY. Figure 19 ASSEMBLY WARNING ! To avoid possible fire or shock, do not pinch wires betw

Turn the switch housing cover clockwise to engage the slots, then securely tighten the two screws (Figure 13). NOTE: Be sure the wires are not pinched between the switch housing and the switch housing cover. 6 FAN BLADE 6-32 x 6mm PHILLIPS BUTTON HEAD SCREWS (2) STRUT Figure 10 SWITCH HOUSING COVER REMOVE AND RETAIN THIS NUT REMOVE AND RETAIN THIS LOCKWASHER Figure 12 LIGHT FIXTURE SWITCH HOUSING COVER 2-1/4" PIPE NIPPLE TIGHTEN TWO 8-32 x 3/8" PAN HEAD SCREWS REINSTALL LOCKWASHER AND NUT SPEED

! WARNING Do not install or use fan if any part is damaged or missing. Call Toll-Free: 1-800-654-3545 This product is designed to use only those parts supplied with this product and/or any accessories designated specifically for use with this product by Emerson Company. Substitution of parts or accessories not designated for use with this product by Emerson Company could result in personal injury or property damage. ! WARNING ! WARNING This Manual Is Designed to Make it as Easy as Possible for Y

6 NOTE: CEILING COVER, SUPPLY WIRES AND OUTLET FAN WIRES OMITTED BOX FOR CLARITY. HANGER BRACKET Figure 14 DOWNROD ASSEMBLY HANGER BALL/ WARNING ! To avoid possible fire or shock, do not pinch wires between the hanger ball/downrod assembly and the hanger bracket. How to Wire Your Ceiling Fan If you feel that you do not have enough electrical wiring knowledge or experience, have your fan installed by a licensed electrician. 1. Connect the green grounding lead from the hanger ball and the green gr

2.Remove the hanger ball from the downrod by loosening the setscrew in the hanger ball until the ball falls freely down the downrod (Figure 1). Remove the pin from the downrod, then remove the hanger ball. Retain the pin and hanger ball for reinstallation in step 9. HANGER BALL DOWNROD PIN SETSCREW Figure 1 3. Separate, untwist and unkink the three motor leads. Route the motor leads through the downrod and seat the downrod in the motor coupling (Figure 2). NOTE: If your ceiling height is nine fe

If flanges are seated incorrectly, loosen the flange screws and retighten according to step 13 in the section “Assembly Instructions”. 5. Tighten the hanger bracket screws to the outlet box, and/or secure outlet box. 6. Interchanging an adjacent (side-by-side) blade pair can redistribute the weight and result in smoother operation. Or use supplied balancing kit to balance blades. 9 10 8 33 24 12 36 10 35 5 4 25 26 15 18 19 9 21 23 24 11 40 7 38 28 29 31 30 32 22 14 13 37 39 34 1 2 16 17 3 18 6 2