The variable speed switch enables you to select the best speed for a particular application. The more you squeeze the trigger, the faster the tool will operate. Use lower speeds for starting holes without a center punch, drilling in metals or plastics, or driving screws. For maximum tool life, use variable speed only for starting holes or fasteners. NOTE: Continuous use in variable speed range is not recommended. It may damage the switch and should be avoided. E FORWARD/REVERSE CONTROL BUTTON (F

WARNING LABEL REPLACEMENT If your warning labels become illegible or are missing, call (888) 848-5175 for a free replacement. The following are PORTER-CABLE trademarks for one or more power tools and accessories: agray and black color scheme; a “four point star” design; and three contrasting/outlined longitudinalstripes. The following are also trademarks for one or more PORTER-CABLE and Delta products: Les elements ci-dessous sont des marques de commerce des outils et des accessoires dePORTER-CA

2. When attaching accessories in the drill chuck, hand tighten the keyless chuck firmly. : Drill may stall (if overloaded or improperly used) causing a twist. Always expect the stall. Grip the drill firmly to control the twisting action and prevent loss of control which could cause personal injury. If a stall does occur, release the trigger immediately and determine the reason for the stall before re-starting. E 9 90550130 PC1800HD hammer drill 4/3/09 2:40 PM Page 10 Operating Instructions Trigg

Do not allow any liquid to get inside charger. : : Burn hazard. To reduce the risk of injury, charge only designated PORTER-CABLE batteries. Other types of batteries may burst causing personal injuryand damage. : Under certain conditions, with the charger plugged in to the power supply, the charger can be shorted by foreign material. Foreign materials of a conductive nature such as, but not limited to, steel wool, aluminum foil, or any buildup of metallic particles should be kept away from charg

Incorrect reassembly may result in a risk of electric shock, electrocution or fire. • Disconnect the charger from the outlet before attempting any cleaning. This will reduce the risk of electric shock. Removing the battery pack will not reduce this risk. • NEVER attempt to connect 2 chargers together. • The charger is designed to operate on standard household electrical power (120 Volts). Do not attempt to use it on any other voltage. SAVE THESE INSTRUCTIONS IMPORTANT SAFETY INSTRUCTION FOR BATT

9, and pull battery pack out of tool. To install a battery pack, align rails (A) Fig. 9 on battery pack with slots on tool and push battery pack onto tool until it locks in place. A B Fig. 9 HOW TO HOLD THE DRILL/DRIVER The front end of the Drill/Driver may be made live if the tool drills into live wiring in the wall. TO PREVENT ELECTRICAL SHOCK, THE HAMMER DRILL/DRIVER MUST BE HELD AS SHOWN IN FIG. 10A. IT’S A DRILL Fig. 10A 11 HOW TO HOLD THE HAMMER DRILL/DRIVER The front end of the Hammer Dri

c) Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock. d) Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of electric shock. e) When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of elect

Repeat until you reach the correct setting. Use this setting for the remaining screws. FG34H5 • For screwdriving, set the collar to the desired setting. If you do not yet know the appropriate setting, proceed as follows: • Set the collar to the lowest torque setting. • Tighten the first screw. • If the clutch ratchets before the desired DUAL RANGE GEARING - FIGURE G The dual range feature of your drill allows you to shift gears for greater versatility. To select low speed, high torque setting (p

So when transporting individual batteries, make sure that the battery terminals are protected and well insulated from materials that could contact them and cause a short circuit. NOTE: LI-ION batteries should not be put in checked baggage. STORAGE RECOMMENDATIONS 1. The best storage place is one that is cool and dry away from direct sunlight and excess heat or cold. 2. Long storage will not harm the battery pack or charger. Under proper conditions LI-ION batteries, can be stored for 5 years or m