Log:
Téléchargements : 14   Taille : 7 mb   Fabricant : Grizzly  
Catégorie : Machines-outils
@name

-16 G0456 Variable Speed Wood Lathe Adjusting Tailstock The tailstock is equipped with a cam-action clamping system to secure it to the lathe bed. When the lever is tightened, a locking plate lifts up and secures the tool rest to the bed. To position the tailstock along the bed: 1. Loosen the quick release and move the tailstock to the desired position (Figure 12). 2. Tighten the quick release. —If the quick release will not lock the tailstock down onto the bed (either too loose or too tight), l

Téléchargements : 6   Taille : 2 mb   Fabricant : Grizzly  
Catégorie : Machines-outils

Téléchargements : 6   Taille : 11 mb   Fabricant : Grizzly  
Catégorie : Machines-outils
@name

#CR8520 PRINTED IN CHINA ...........................................................................................................................................................................................................................................................................................................................................................................................................................................................................................

Téléchargements : 10   Taille : 8 mb   Fabricant : Grizzly  
Catégorie : Machines-outils
@name

Pump damage will cccur if it is run for a period of time without coolant. To perform regular maintenance on the cutting fluid system: 1. Remove the access cover at the rear of the lathe (Figure 56). Figure 57. Coolant pump switch. Figure 56. Coolant pump and reservoir. -42- G0509 & G0509G 16" x 40" Lathe SECTION 7: SERVICE Troubleshooting Review the troubleshooting and procedures in this section to fix your machine if a problem / .✓I® develops. If you need replacement parts or you are u

Téléchargements : 6   Taille : 300 kb   Fabricant : Grizzly  
Catégorie : Machines-outils
@name

Alignment of longitudinal bed slide ways in vertical plane: 0.04mm (0.0015") 0.018mm b. Parallelism of transverse direction: 0.04mm (0.0015") in 1000mm (39.370") 0.03mm 0.0007" 0.0012" G2 Parallelism of tailstock to longitudinal motion carriage: a. In vertical plane 0.02mm in 500 mm b. In horizontal plane 0.02mm (0.0008") in 500mm (19.685") 0.01mm 0.01mm 0.0004" 0.0004" G3 Cam action of spindle 0.015mm (0.0006") 0.008mm 0.0003" G4 Spindle nose runout 0.01mm (.0004") 0.005mm

Téléchargements : 5   Taille : 4 mb   Fabricant : Grizzly  
Catégorie : Machines-outils
@name

Mill/Drill Coarse Downfeed Handle 26. Mill/Drill Head Fine Downfeed Knob 27. Mill/Drill High/Low Speed Selection Lever 28. Mill/Drill Variable Speed Adjustment Knob 29. Mill/Drill Power Indicator Light 30. Mill/Drill ON/OFF, Emergency Stop Switch G0516 Lathe/Mill 1 2 3 4 5 6 7 9 10 11 13 14 15 12 8 1 2 3 4 5 6 7 9 10 11 13 14 15 12 8 Figure 3. The picture above shows important accessories and tools that are included with the Model G0516. Please take some time to identify these items. Similar to

Téléchargements : 0   Taille : 7 mb   Fabricant : Grizzly  
Catégorie : Machines-outils
@name

When the dial indicator needle stops moving, there will be no spindle end-play and no bearing preload. it is essential that you find this point without tightening the spindle nut further and preloading the bearings. if you think you may have gone past the zero end-play point, take the time to unload the bearings as instructed in Step 8, then retighten the spindle nut until you know you have reached the correct setting. Tip: Since it takes great effort to properly turn the spindle nut, you may fi

Téléchargements : 5   Taille : 2 mb   Fabricant : Grizzly  
Catégorie : Machines-outils
@name

Téléchargements : 4   Taille : 41 kb   Fabricant : Grizzly  
Catégorie : Machines-outils
@name

330 lbs. Length/Width/Height.......................................................................................................................46 x 22 x 16-5/8 in. Foot Print (Length/Width).................................................................................................................47-1/2 x 12-1/2 in. Shipping Dimensions: Type.................................................................................................................................................

Téléchargements : 4   Taille : 4 mb   Fabricant : Grizzly  
Catégorie : Machines-outils
@name

WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC. #BL86839 PRINTED IN CHINA .......................................................................................................................................................................................................................................................................................................................................................





catégories