Évaluations - 0, GPA: 0
(
)
)
|
Par ce dispositif a également d'autres instructions :
Facilité d'utilisation
BB856-90901 Greenwich Eng front.pdf 1 10/09/2012 16:54
HP StoreOnce 4420 Backup
Further information about networks
HP StoreOnce 4430 Backup
1 About your HP StoreOnce Backup system
4 Connect the hardware
NOTE: The HP StoreOnce Backup system does not support the IPv6 protocol.
The HP StoreOnce Backup system is a disk-based storage appliance for backing up host
1. Always use the supplied power cords to connect the HP StoreOnce Backup system to the
network servers or PCs to target devices on the appliance. These devices are configured
mains power supply. For detailed safety information, see the Safety Guide on the
The physical network ports provide three network configuration modes.
as NAS Share, Virtual Tape Library or Catalyst Store targets for backup applications.
CD-ROM.
• Single Port Configuration: The HP StoreOnce Backup system is connected to one
To find out which backup applications are compatible with HP StoreOnce functions go to
2. Use any CAT-5E network cable (also supplied with the product) to connect LAN Port1
network; only one network port is used (Port 1).
www.hp.com/go/ebs.
1GbE to a 1 Gigabit Ethernet network.
• Dual Port Configuration: The HP StoreOnce Backup system is connected to two
The HP StoreOnce Backup system has two 1GbE ports and two 10GbE ports. You must
different networks. Both network ports are used.
Start here
connect to the 1GbE port (labelled LAN Port1 1GbE) to discover the HP StoreOnce Backup
• High Availability (Bonded) Configuration: Both network ports are used, but the two
TIP: To find out more about configuring and using NAS target devices, FC and iSCSI
system on your network. This is also the recommended port for running the Web
ports are bonded to provide port failover. This mode also provides load balancing
virtual tape libraries and Catalyst Stores, see the HP StoreOnce Backup system User
Management Interface.
across the two network ports
Guide on the CD-ROM.
The 10GbE ports are available for backup and replication traffic. They must be
The default network configuration is single port with DHCP enabled. This can be
configured separately, after installation on the Network (Configuration) page of the Web
amended after installation using StoreOnce CLI net config commands.
HP StoreOnce Backup system upgrade kit
Management Interface.
If dual port configuration is required, the networks must be on different sub-nets.
The Capacity Upgrade Kit is an optional 12-disk expansion model. Up to three expansion
LAN Port1 1GbE (the lower port) must always be connected, even if you are using the FC
The High Availability mode is the recommended option, because it provides port failover,
models may be installed at the same time as the HP StoreOnce Backup system or added
ports to back up and restore data to the HP StoreOnce Backup system, because the Web
but both network ports must be connected to the same switch and it must support port
later. A license is always required for the Capacity Upgrade and is included with the kit.
Management Interface requires an Ethernet connection to set up devices.
bonding. If you select the high availability bonded network mode, the bonded ports must
Be sure to order the correct kit for your system:
be of the same speed. You can bond a 1GbE LAN port with the other 1GbE LAN port,
and you can bond a 10GbE LAN port with the other 10GbE LAN port, but you cannot
• HP StoreOnce 4220/4420 Upgrade Kit (12 x 1TB Disks) for HP StoreOnce 4220 and
bond a 1GbE LAN port with a 10GbE LAN port.
4420 Backup
• The HP StoreOnce Backup system is scalable from 12 to 48 disks. Up to three
For further information please refer to the Installation and Configuration Guide and the
12-disk shelves may be connected to the base 12-disk unit.
• HP StoreOnce 4430 Upgrade Kit (12 x 2TB Disks) for HP StoreOnce 4430 Backup
HP StoreOnce CLI Reference Guide on the CD.
• The host is the network server that you wish to back up.
• The HP StoreOnce Backup system should be connected to Gigabit Ethernet.
Connecting to a Fibre Channel SAN
100 Base-T Ethernet will limit performance.
The HP StoreOnce Backup system is supplied with the correct FC card pre-installed.
• For more detailed information about installing, configuring and using the HP
StoreOnce Backup system, see the Installation and Configuration Guide and the
However, you must still connect the HP StoreOnce Backup system to an Ethernet network
User Guide on the HP StoreOnce Backup CD-ROM.
in order to use the Web Management Console.
2 IMPORTANT – Retrieve your license entitlement
Please note that devices created on the HP StoreOnce Backup system can be accessed by
certificates (if purchased)
all hosts on the SAN unless you configure zones on the Fibre Channel Fabric/Switch.
Licensing is used to enable optional product functionality, such as extra disk capacity,
Connecting to the Capacity Upgrade Kit (optional)
Replication, Catalyst or other future features. If you have purchased any of these features,
1 USB keyboard connectors
Install the rail kit and expansion model immediately below or above the HP StoreOnce
you should activate the license as soon as possible.
2 Power sockets
Backup system, as described in Section 3.
3 Video/monitor connector
C
Replication and Catalyst License Entitlement Certificates are supplied electronically when
4 iLO 2 port – do NOT use for data connection
1. To ensure correct keying, first connect the supplied cable to the IN connector on the
M
the product is purchased. For extra disk capacity the appropriate License Entitlement
5 LAN Port1 1GbE – always used for data connection
rear of the Capacity Upgrade Kit.
Y
Certificate is supplied with your product. This is a paper document that contains all the
information you need to obtain your unique License To Use key, which you can then enter
6 LAN Port2 1GbE – used for data connection only if network
2. Connect the other end of the cable to the port labeled “Port 1E” on the RAID P212
CM
into the Web Management Interface. The Entitlement Certificates are shipped in clearly
configured for multiple 1GbE port configurations
PCI-e card on the rear of the HP StoreOnce Backup system.
MY
marked card envelopes with your HP StoreOnce Backup system. These are valuable items
3. Use the supplied power cords to connect the Capacity Upgrade Kit to the mains
CY
so, to prevent them becoming lost, please ensure they are identified and put safely to one
7 10GbE card
power supply.
CMY
side during unpacking.
8 Fibre Channel card
K
9 RAID cards (all systems)
Entitlement certificates for iLO2 Advance Packs and Smart Array Advance Packs are also
10 RAID card (HP StoreOnce 4430 only)
© 2012 Hewlet -Packard Development Company, L.P.
supplied with the HP StoreOnce Backup system.
11 SAS expander card
Printed in Hungary
It is strongly recommended that all licenses are redeemed as soon as possible. Go to the
Webware site - webware.hp.com. For detailed information about activating licenses refer
www.hp.com
to the HP StoreOnce Installation and Configuration Guide on the StoreOnce CD.
NOTE: The RAID cards in the HP StoreOnce 4420 Backup system have two ports;
the RAID cards in the HP StoreOnce 4430 Backup system have four ports.
To ensure that the HP StoreOnce Backup system is discovered successfully, install it on
the same subnet as the host machines that will access it. Typical installations have the
HP StoreOnce Backup system connected to the same Gigabit network switch as the host
3 Install the rack rails and unit(s)
machines that are carrying out the backups in order to gain optimum performance.
Rail kits are supplied to allow you to install the HP StoreOnce Backup system and Capacity
Upgrade Kit into suitable racks. Please refer to the Installation Instructions, shipped with the
rail kits.
Install the expansion model immediately below or above the HP StoreOnce Backup system.
Important safety information
Server
Server
Server
Connect the hardware continues overleaf
Use extreme caution when installing and pulling the unit out from the rack; it can slip and
Ethernet
fall, causing damage to the HP StoreOnce Backup system or injury. HP is not responsible
switch
for any damage or injury caused by the mishandling of the HP StoreOnce Backup system.
LAN
Supplied cable
IMPORTANT: Be sure to read the safety information on the rail installation documents
and follow the instructions for lifting and installing devices carefully. Refer also to the
Safety Guide and the Installation and Configuration Guide on the HP StoreOnce
Backup CD for detailed safety information.
HP StoreOnce Backup
WARNING: Ensure that sufficient personnel are on hand to support the product(s)
during the installation process. Use of the appropriate lifting device is recommended
as an installation aid.
BB856-90901
... Ce manuel est également adapté pour les modèles :
données dispositifs de traitement - HP D2D2502i SmartBuy Backup System (1.02 mb)
données dispositifs de traitement - HP D2D2503i Backup System (1.02 mb)
données dispositifs de traitement - HP D2D2503i SmartBuy Backup System (1.02 mb)
données dispositifs de traitement - HP D2D2504i Backup System with Replication Promo LTU (1.02 mb)