Log:
Trier : Nom ↑   Téléchargements   Évaluation   Taille ↑  

RIDGID IN625301AV

Téléchargements : 12 Taille : 5 mb    Fabricant : RIDGID  
Catégorie : matériel de pompage

head cap screw 4 12 33478 WL008400AV Fan * 1 13 17943 ST072224AV 3/8 inch Compression Elbow 1 14 -WL015304SJ Belt kit (Includes #10, 12, check valve, & ferrules) * 1 REPAIR PARTS KITS s l -- WL211201SJ WL211100AJ Valve plate kit (Includes #2-7) Head bolt kit (Set of 4 ea., part #11) 1 1 † = Standard Hardware Item --= Not Available * = Considered wear items 17 catalog no. OF25150A Model no. OF25150A serial no. _____________ _ The model and serial numbers may be found on your unit. You should reco

RIDGID GP90150A

Téléchargements : 5 Taille : 2 mb    Fabricant : RIDGID  
Catégorie : matériel de pompage

IN629100AV 12/08 Printed in U.S.A. Table of Contents Section Page Table of Contents . . .. . .. . .. . .. . ..2 Safety Instructions . .. . .. . .. . .. . ..3 Safety Signal Words . . . . . . . . . . . . .3 Before Using the Air Compressor . . . . . . . . . . . . . . . . . . . .3 Spraying Precautions . . . . . . . . . . . .5 Breathable Air Warning . . . . . . . . . . .5 Warning Labels . . . . . . . . . . . . . . . . .6 Glossary of Terms . .. . .. . .. . .. . ..7 Unpacking and Checking Content . . .

RIDGID R1001

Téléchargements : 1 Taille : 2 mb    Fabricant : RIDGID  
Catégorie : Les machines à rectifier

Do not remove the disc flange. OPERATION • Make sure the flats on the bottom of the disc flange are engaged with the flats on the spindle. • Place the grinding wheel over the spindle. • Thread the clamp nut on the spindle with the flat side of the nut facing up. • Fit the raised, small diameter portion of the clamp nut into the hole in the wheel and finger tighten. WARNING: Always install a grinding wheel with the depressed center against the disc flange. Failure to do so will cause the grinding

RIDGID 204830-OS

Téléchargements : 0 Taille : 263 kb    Fabricant : RIDGID  
Catégorie : Autres accessoires pour la maison

Securing shelf for transport: 1. To minimize movement during transport, make sure the shelf front is located behind the stop tabs on each side of the box. 2. Once the box is on-site the shelf can be moved forward by slightly lifting the front edges over the stop tabs. The shelf bottom should always lie flat on the runners when finished adjusting the shelf. "RapidPassThru"-1.eps STOP TAB HAND TOOL STORAGE SCREWDRIVER Figure 8 TO INSTALL RAPID PASS™ GROMMET (Model 2048-OS and Model 204830-OS) TOOL

RIDGID 1822-I

Téléchargements : 12 Taille : 2 mb    Fabricant : RIDGID  
Catégorie : Machines à coudre

51 1822-I WARNING! Read this Operator’s Manual carefully before using this tool. Failure to understand and follow the contents of this manual may result in electrical shock, fire and/or serious personal injury. OPERATOR’S MANUAL • Francais – 25 • Castellano – pag. 51 1822-I WARNING! Read this Operator’s Manual carefully before using this tool. Failure to understand and follow the contents of this manual may result in electrical shock, fire and/or serious personal injury. Pipe and BoltThreading M

RIDGID 5228

Téléchargements : 0 Taille : 424 kb    Fabricant : RIDGID  
Catégorie : Jig Saw et

Failure to understand and follow the contents of this manual may result in electri- cal shock, fire and/or serious personal injury. 5228 Double Insulated Variable Speed, Dual Action Reciprocating Saw Table of Contents General Safety Information Work Area Safety ........................................................................................................................................................2 Electrical Safety...................................................................

RIDGID R150FSA

Téléchargements : 1 Taille : 686 kb    Fabricant : RIDGID  
Catégorie : Clouteuses

RIDGID OF45150B

Téléchargements : 11 Taille : 3 mb    Fabricant : RIDGID  
Catégorie : matériel de pompage

Turning counterclockwise will lower air pressure at the outlet. Fully counterclockwise will shut off the flow of air completely. Close Open 5. Tank Pressure Gauge. Gauge shows pressure in air receiver indicating compressor is building pressure properly. 6. ASME Safety Valve. This valve automatically releases air if the tank pressure exceeds the preset maximum. 7. Air Outlet Fittings. These fittings are 1/4” universal-style quick connect fittings and allow rapid tool changes. 8. Air Filter. The a

RIDGID TP1300LS

Téléchargements : 4 Taille : 706 kb    Fabricant : RIDGID  
Catégorie : Avions

WARNING: To reduce the risk of injury, the user must read and understand the operator’s manual before using this product. Thank you for buying a Ridgid product. OPERATOR'S MANUAL 13 in. THICKNESS PLANER TP1300LS SAVE THIS MANUAL FOR FUTURE REFERENCE 1 Repeat Cut A- - 1 1 1 1 1 3 3 2 2 " " 4 4 4 4 8 1 1 1 3 1/8 3/32 1/16 1/32 0 2.5 2 1.5 1 .5 0 Ind I Cut 6 5 4 2 1 0 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 3 TABLE OF CONTENTS • Introduction ...........................................................

RIDGID R3000

Téléchargements : 0 Taille : 588 kb    Fabricant : RIDGID  
Catégorie : Jig Saw et

Note: Advises you of additional information concerning the operation or maintenance of the equipment. 5 SPECIFICATIONS Input .................................................................................................................. 120 Volts, 60 Hz, AC Only, 9.0 amperes No load speed ............................................................................................................................................... 0-2800 /min. Stroke Length.....................................





catégories