WARNING TO REDUCE THE RISK OF FIRE ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING: a. Use this unit only in the manner intended by the manufacturer, if you have questions, contact the manufacturer. b. Before servicing or cleaning unit, switch power off at service panel and lock panel to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, to the service panel. CAUTION For
Charcoal filters may need to be replaced more frequently depending on cooking style. 1. Install metal bracket* onto metal filter from hood by sliding one end of the metal bracket underneath the backside of the gray handle as shown. 2. Push two corner tabs into metal filter frame to lock them in. If pushing tabs is difficult, gently lift up on the corner lip of the bracket near the gray handle and push down on the corner tab. (Fig.1) 3. Install charcoal filter onto metal bracket with platic si
Place cap over threaded end of remote blower wiring and secure by turning clockwise. 1. Place 10” round adapter on top of hood and 2. Install threaded end of remote blower wiring secure with (4) M4x8 screws. Connect 10” through external blower wiring knock out round duct work to 10” round adapter. located inside the hood. CBE-1000 / PBN-1000A: WIRING DIAGRAM 4. Connect 6 pin male connector from remote blower wiring to 6 pin female connector on control board wire inside hood. Secure green ground
If available, also refer range manufacturer’s height clearance requirements and recommended hood mounting height above range. Vertical Ducting: 6” round minimum (CBI-xxxB blower) 10” round minimum (PBI-1100A and remote blowers) Horizontal Ducting: 3-1/4”x10” minimum (CBI-xxxB blower) No horizontal option available for PBI-1100A or remote blower DAMAGE-SHIPMENT / INSTALLATION: • Please fully inspect unit for damage before installation. • If the unit is damaged in shipment, return the unit to the
Do not place charcoal filters in the dishwasher or soak them in soapy water. Under normal usage (1 hour per day) filters should be replaced every 3 - 4 months. Charcoal filters may need to be replaced more frequently depending on cooking style. 1. Install metal bracket* onto metal filter from hood by sliding one end of the metal bracket underneath the backside of the gray handle as shown. 2. Push two corner tabs into metal filter frame to lock them in. If pushing tabs is difficult, gently lift
ALL-M90ABX ALL-M90AWX ALL-E42AWX ALL-E42ABX RANGE HOOD - Installation instructions HOTTE PER CUISINE - Notice d’utilisation...Pag. 25 CAMPANA EXTRACTORA - Manual de utilizacion...Pag. 48 CAPPA ASPIRANTE - istruzioni per l’uso...Pag. 73 - 2 - SAFETY INSTRUCTIONS..................................................................................................pag. 4 LIST OF MATERIALS...........................................................................................................pag. 7 DUC
Insert bottom side of carbon filter where the tab cut-outs are first. (Fig.2) 4. Push charcoal filter down until it clicks, locking tabs in place. 5. Installation complete. Install metal filter into range hood. Corner Tabs JUN07.0201 Fig. 1 Fig. 2 *note: Filter bracket appearance may be slightly different from the bracket pictured.
For the liner installation, only the bottom of the custom hood is needed. Do not finalize the entire custom hood yet, because an opening is needed for the power pack. 0) c o (0 Û- Liner Model Power Pack Model Custom Hood Exterior Width *Inside Width (A) *Inside Depth (B) Without Backboard **With Backboard AK0800AS AK8000AS and AK8100AS 30 inches 28 1/2” 17 1/2” - 20 1/2” 17 1/8” - 20 1/8” AK0836AS 36 inches 34 1/2” AK0806AS AK8200AS 36 inches 34 1/2” 20 1/2” - 23 1/2” 20 1/8” -
4 INSTALLATION Ducting Calculation Sheet....................................... 5 Mounting Height & Clearance................................ 6 Ducting Options........................................................... 7 Specifi cations ............................................................... 8 Electrical ......................................................................... 9 Mounting the Range Hood...................................... 10 CBIxxxB and PBI-1100A Internal Blowers.......
INSTALLATION MOUNT HEIGHTS DUCTING (AK8000AS, AK8100S, AK8200S) Min 24"-Max 32" 36" Minimum mount height between range top to hood bottom should be no less than 24". Maximum mount height should be no higher than 32". It is important to install the hood at the proper mounting height. Hoods mounted too low could result in heat damage and fire haz- ard; while hoods mounted too high will be hard to reach and will loose its performance and efficiency. If available, also refer range manufacturer's hei