For example, if you wanted to secure Door 5, at the following prompt: SECURE DOOR 1 2 3 4 5 6 7 8 Press 5 then ENT. The display will read: SECURE DOOR 1 2 3 4 X 6 7 8 This indicates that all doors are at a normal state, except for Door 5, which is secured. 16. Press ESC to leave this subfunction, or enter another door number to unlock. NOTE: Each of these subfunctions act as a toggle. To return a door to its normal state, follow the same procedure you used to change its state. For example, if Do

B 1/01 Model SAVS20ADT-1 or SAVS20ADTG UL File No. S1632 IMPORTANT! PROPER INTRUSION PROTECTION For proper intrusion coverage, sensors should be located at every possible point of entry to a home or commercial premises. This would include any skylights that may be present, and the upper windows in a multi-level building. In addition, we recommend that radio backup be used in a security system so that alarm signals can still be sent to the Customer Care Center in the event that the telephone line

200 PLUS is a user-friendly security system that monitors your site’s detectors and alarms. Fully programmable, the FOCUS. 200 PLUS allows you to control hundreds of critical security functions from one menu-driven interface as simple to use as the automated teller machine (ATM) at your local bank. The ADT FOCUS. 200 PLUS consists of a central control unit, an operating panel, and up to 255 protection points. The control unit is protected by a heavy-gauge steel cabinet and protected by a tamper

3 ARMING ....................................................................................... 3 Arming The System Prior To Leaving ..................................... 3 Arming The System Without Leaving ..................................... 3 System Not Arm (Ready Light Off) .................................. 4 DISARMING ...................................................................................... 5 Disarming Upon Entering The Premises ................................ 5 ALARM CONDI

The instructions for the commands listed in this reference are intended to replace those instructions in the Security System Owner’s Manual. Please refer to the Owner’s Manual for the operation of your new security system and its other basic Function List features. NOTE: This supplement should be placed inside the Security System Owner’s Manual. Access Level Control ............................................................... 3 Door Control Command 46 .........................................

Ensure that no zones are unintentionally 4 bypassed when arming your system. Zones cannot be bypassed once the system is armed. Bypassed zones are automatically cancelled each time the system is disarmed and must be bypassed again, if required, before the next arming. Bypassing Zones With the system disarmed. 1. Press to enter the function menu. The keypad will display “Press 4 for < > Zone Bypass”. 2. Press or , then your [access code] (if required). The keypad will display “Scroll to < > Bypas

All remaining points above 568 will report as fire alarm points. Document 50934 Rev B 5/15/00 PN 50934:B To access Type Mode, press the MODE key followed by the 4-digit code 8973 and then press the [ENTER/STORE] key. The ADT-UDACT will display three digits. For example, initial entry will display 01 0. To access Type Mode, press the MODE key followed by the 4-digit code 8973 and then press the [ENTER/STORE] key. The ADT-UDACT will display three digits. For example, initial entry will display 01

This will turn off all C304 modules and Notification Appliance Circuits, temporarily turns off resettable power to 4-wire detectors, causes a 'System All Normal' message to be displayed on the ADT-LCD40 and sends a 'System Reset' message to the FACP display, printer and Unimode 200 history files. It also turns on all system LEDs, piezo sounders and LCD display segments as long as the Reset switch is held (lamp test). Any alarm or trouble that exists after a Reset will resound the system. Documen

If the sounder does not sound, CALL FOR SERVICE IMMEDIATELY. 4. Fault zones. Open each protected door and window in turn and listen for three beeps from the keypad. Identification of each faulted protection point should appear on the display. The display will clear when the door or window is closed. - 32 Testing the System (cont'd) 5. + 1 (Security Code) OFF Walk in front of any interior motion detectors (if used) and listen for three beeps. The keypad should display the identification of the de

Connection to party lines is subject to state tariffs. This equipment is hearing-aid compatible. Industry Canada NOTICE: The Industry Canada Label identifies certified equipment. This certification means that the equipment meets telecommunications network protective, operational and safety requirements as prescribed in the appropriate Terminal Equipment Technical Requirements document(s). The Department does not guarantee the equipment will operate to the user’s satisfaction. Before installing t