Log:
Trier : Nom ↑   Téléchargements   Évaluation   Taille ↑  

Sterling EX913

Téléchargements : 1 Taille : 2 mb    Fabricant : Sterling  
Catégorie : Les machines à rectifier

1. Turn the main disconnect to the ON position. 2. Start the granulator by pressing the start button at the operator station. 3. Load feedstock at a uniform rate that does not exceed the capacity of the machine; see Table 1: Granulator Specifications. 4. For color and/or material changes, allow all existing material to clear the granulator and any downstream equipment before stopping the machine. Doing so reduces cleaning requirements. 4-4 Cleaning Out the Granulator To open the granulator and o

Sterling EX918

Téléchargements : 1 Taille : 2 mb    Fabricant : Sterling  
Catégorie : Les machines à rectifier

Once clearance is established, fully tighten the adjustment cam screws. 6. Repeat steps 1 through 5 for all bed combs. 7. Fully tighten all bed comb adjustment screws to 12 ft/lbs. 5-5 Adjusting the Sensitivity of the Optional Bin LevelMonitor !!! DANGER !!! Because electrical power must be supplied to the sensor to permit testing andadjustment, it is EXTREMELY VITAL that you secure the machine for normaloperations. Do so by closing the cutting chamber and hopper access door, which returns thesa

Sterling TUBULAR GAS FIRED DIRECT SPARK PROPELLER UNIT HEATERS GG-45

Téléchargements : 5 Taille : 3 mb    Fabricant : Sterling  
Catégorie : matériel de pompage

5. Seal all vent pipe joints and seams to prevent leakage. Use General Electric RTV-108, Dow- Corning RTV-732, or equivalent silicone sealant with a temperature rating of 500 deg. F, or 3M # 425 aluminum foil tape (or equivalent). The vent system must be installed to prevent collection of condensate. Pitch or 3M #425 aluminum foil tape (or equivalent). 7. Avoid running vent pipe through unheated spaces. When this cannot be avoided, insulate the pipe to prevent condensation of moisture on the wal

Sterling BP818

Téléchargements : 6 Taille : 3 mb    Fabricant : Sterling  
Catégorie : Les machines à rectifier

Granulator .. Bill of lading .. Packing list drawings, electrical schematics, and manual from the base evacuation area. You can now have the machine lifted from the skid. A forklift is ideal for the purpose, but take care to properly position the forks between the casters and the centrally mounted evacuation pipe from the side of the machine. (See Figure 5) Figure 5: Lifting the Granulator ! CAUTION ! Do not attempt to lift the granulator by means of any shaft or protruding member, ESPECIALLY TH

Sterling TUBULAR GAS FIRED DIRECT SPARK PROPELLER UNIT HEATERS GG-105

Téléchargements : 49 Taille : 3 mb    Fabricant : Sterling  
Catégorie : matériel de pompage

RECORD THE UNIT MODEL AND SERIAL No.(s) IN THE SPACE PROVIDED. RETAIN FOR FUTURE REFERENCE. Model No. Serial No. FOR YOUR SAFETY Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance. FOR YOUR SAFETY WHAT TO DO IF YOU SMELL GAS Do not try to light any appliance. Do not touch any electrical switch; do not use any phone in your building. Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions. If

Sterling TUBULAR GAS FIRED DIRECT SPARK PROPELLER UNIT HEATERS GG-120

Téléchargements : 5 Taille : 3 mb    Fabricant : Sterling  
Catégorie : matériel de pompage

For unit installations in U.S.A. above 2,000 ft. (610m), the unit input must be derated 4% for each 1,000 ft. (305m) above sea level; refer to local codes, or in absence of local codes, refer to the latest edition of the National Fuel Gas Code, ANSI Standard Z223.1 (N.F.P.A. No. 54), (also refer to Table 6). 4 5 Figure 2 - Dimensional Drawing – Tubular 30 thru 120 Propeller Unit Heater DIMENSIONS .XXX STANDARD UNITS DIMENSIONS IN PARENTHESIS (XXX) MILLIMETERS INSTALLATION Do not install unit hea

Sterling BJ1-625

Téléchargements : 29 Taille : 2 mb    Fabricant : Sterling  
Catégorie : Les machines à rectifier

1-1-2 Safety Symbols Used in This Manual The following safety alert symbols are used to alert you to potential personal injury hazards. Obey all safety messages that follow these symbols to avoid possible injury or death. DANGER indicates an imminently hazardous situation, which, if not avoided, will result in death or serious injury. WARNING indicates a potentially hazardous situation or practice which, if not avoided, could result in death or serious injury. CAUTION indicates a potentially haz

Sterling BP814

Téléchargements : 0 Taille : 3 mb    Fabricant : Sterling  
Catégorie : Les machines à rectifier

If the drive belts have to be replaced, follow the procedure in Section 6-2-1 up to Step 6. Then release the belt from tension by fully unscrewing the tie rods. Slip off the belts, and replace them with new ones. Continue with the procedure for adjusting the belt tension. 6-3 Removal and Replacement of the Screen NOTE: A qualified operator/maintenance mechanic should carry out this procedure. 1. Switch the machine off and lockout power by turning the disconnect switch to “OFF”, or remove the fus

Sterling Mobility Scooter

Téléchargements : 26 Taille : 905 kb    Fabricant : Sterling  
Catégorie : Fauteuils roulants

This Owner’s Manual will familiarise you with the scooter and its features. It contains guidance on everyday usage and general care in addition to information on the high quality standards which we adhere to and details about the warranty. Your scooter will reach you in excellent condition having been personally inspected before leaving the factory. By following the guidelines for maintenance on page 30 your scooter will maintain its first class condition and give you years of complete reliabili

Sterling TUBULAR GAS FIRED DIRECT SPARK PROPELLER UNIT HEATERS GG-90

Téléchargements : 21 Taille : 3 mb    Fabricant : Sterling  
Catégorie : matériel de pompage

Power venter improperly wired. 2. Main burner did not light on call for heat. 3. Defective control board. 4. Loss of pressure. Pressure switch not made. 1. Check power venter circuit per wiring diagram. 2. Heater is in lockout mode check flash code table for problem. 3. No flash codes present along with no call for heat, replace control board. 4. Check venting for blockage. Check tubing for blockage or hole. Check spud for blockage. 36 Table 10A - Troubleshooting with LED Indicator Assistance fo





catégories