When the desired memory location is lit, press the SCAN button again to select. 4. The DIALOGUE RC automatically dials the number selected. 5. Press the ON/OFF Figure 16 button to hang up. Dialing using the Remote Transmitter A. With Scan function on: 1. Press the Remote Transmitter to begin scanning. FLASH/PAUSE REDIAL MUTE ON/OFFHEADSET MIC Figure 17 2. When the desired memory location is lit, press the Remote Transmitter. The DIALOGUE RC automatically dials the number selected. 3. Press the R

3. Press to select ASCII (or to not select). 4. Next, the screen summarizes the ASCII mode settings and then asks if you want to change modes . 5. Type Y to change. Press or to answer the rest of the prompts related to ASCII data format. 6. When finished, the screen shows the set- ting you selected: , for example. 7. Dial the telephone number as you usually would. 8. Conduct your conversation in the normal fashion. After the conversation is over, hang up and turn off your TTY. It will auto- mati

These Operating Instructions and the associated Quick Operating Guide provide you with the information you need to use your XL-40 effectively, easily and safely. Read this manual thoroughly before using your telephone. Keep the manual near the telephone for easy reference. Warranty Service Your telephone is designed to provide years of quality service. But, should the phone malfunction and the Trouble-shooting Chart on page 12 not resolve the problem, follow the Warranty procedure on page 19. Sa

Please read the Operating Instructions booklet to learn more about the advanced features of the Q90D. Quick Guide Ameriphone products are manufactured by Clarity®, a Division of Plantronics, Inc. 4289 Bonny Oaks Dr., Ste. 106, Chattanooga,TN 37406 VOICE (800) 426-3738 TTY (800) 772-2889 © 2004 Plantronics, Inc. 79040.000 B2/04. Installing and Using Your Q90D Installing and Using Your Q90D Setting Up Your Q90D Lock Switch 1. Slide the LOCK switch (which is located on the right side of the unit be

• Setup special features Installing the Backup Batteries To add extra brightness to the Dialogue XL-25s’s ring flasher when you receive calls, install one 9 Volt alkaline battery (not included). Note: For your safety always unplug the phone line before you install or replace the backup battery. 4 Figure 3 To install new battery: 1. Slide open the battery compart-ment cover on the bottom of the telephone, (Figure 3). 2. Install one fresh 9-volt battery. The battery indicator on the base unit will

Recording Your Outgoing Voice Message Your Easy Recall Answering Machine already comes with the following pre-recorded, outgoing voice message: “Please leave a message after the tone.” Follow these directions to program a personal outgoing voice message. Make sure the machine is ON. Remember, your personal message will override the factory installed one. 1. Simultaneously press and hold down the REC/ERASE and SLOW keys for 2 seconds. 2. When you lift your fingers, the number 29 will appear in th

3. Press the MEMORY b button and then the desired MEMORY button (Figure 24) to store this number as the second phone number in the same memory location. Making and Answering VCO Calls A person with hearing loss who uses their voice can use voice carry over (VCO) through the toll-free local relay service to communicate with a hearing person. In a VCO (voice carry over) call, the hard of hearing person speaks directly to the other party. The Communications Assistant (CA) relays the response from t

3 E N G L I S H Important Safety Instructions CAUTION: Users should not attempt to make such connections themselves, but should contact the appropriate electric inspection authority, or electrician, as appropriate. The Ringer Equivalent Number is an indication of the maximum number of terminals allowed to be connected to a telephone interface. The termination on an interface may consist of any combination of devices subject only to the requirement that the sum of the Ringer Equivalent Number of

1. Insert four AA alkaline batteries for back-up in case of AC power outage. 2. Decide if you want the phone to sit on a desk or hang on the wall. 3. Connect the telephone components. 4. Program up to 12 telephone numbers to call with the press of a memory button. 5. Set up special features Installing the Backup Batteries If there is a power outage, the XL-50 will operate for up to 48 hours with four AA alkaline backup batteries (not included). If the phone is not in use, the batteries will stay

Help from Ameriphone For help with using your DIALOGUE JB-20 , call our Customer Relations department at 800-894-3005. Please make sure your DIALOGUE JB-20 package includes the items shown in Figure 1. Base Unit CHAPTER 3 FEATURES IDENTIFICATION RINGER TONE selector HOLD button Ringer control switch (volume) Audio Output jack Tone / Pulse switch Emergency buttons Braille characters Raised letters for easy identification REDIAL button MEMORY button HANDSET VOL control (volume) FLASH button PROG b