WARNING:(EXPLoSION HAZARD) This unit containsunive6almotors,which spark duringnormal operation. Donot use in areas contaminatedbyvolatileorflammablematerialsas these sparks may ignite the contaminates and cause a dangerous explosion. WARNING:(HARMFULFUMES) The filters used in this unitwillremovesolid padiculateONLY,and do not eliminate fumesand gasesthat may be a health hazard Failureto observethepresenceof such fumescouldcause seriousillnessordeath. CAUTION:(SHOCKHAZARD) To insure continuedprot
sT. LOU|S, MO.63115 Dust 3r4.385.5178 FAX:314.385.3254 OPERATING & PAFITSLIST INSTRUCTIONS Gollector Read inslructions carefully betore attempting to assemble, inslall, operate, move, inspecl or seruice yourdust cottector! Betain insvuctions for luture reference, Description These dust co leclors aredesgned to help malntain clean, sale conditions around dusl creatingmachinesin workshops and lactories. The flexible hose incllded wilh each unit can be hookeddirectlyonlo lhe dusr creating machine.S
e. NEVER smoke or allow a spark or flame in vicinity of the battery or engine. f. Be extra cautious to reduce risk of dropping a metal tool onto the battery. It might spark or short circuit the battery or other electrical parts that may cause an explosion. g. Remove personal metal items such as rings, bracelets, necklaces, and watches when working with a lead-acid battery. A lead-acid battery can produce a short circuit current high enough to weld a ring or the like to metal, causing a severe bu
The yellow light will be on and the meter will indicate low current. BATTERY CHARGE - After testing the battery, the control will select a charging rate suitable for the voltage and state of charge of the battery. A small battery, or a nearly charged battery will cause the charger to rapidly step down in current to avoid heating and gassing. FINISH CHARGE - In order to reach a 100 % state of charge on the battery, a 3 hour finish cycle has been programmed into the charger control. During this cy
Do not operate charger in a closed-in area, or restrict ventilation in any way. e. Do not set a battery on top of charger. 16. DC CONNECTION PRECAUTIONS a. Connect and disconnect dc output clips only after setting any charger switches to off position and removing ac cord from electric outlet. Never allow clips to touch each other. b. Attach clips to battery posts and twist or rock back and forth serval times to make a good connection. This tends to keep the clips from slipping off terminals and
SAFETY.WARNINGS& CAUTIONS CAUTION: 1. FAILURETO OBSERVETHEFOLIOW. (ArRFLOWBLOCKAGE) ING PRECAUTIONS COULDBESULTIN SE- Sinca €xhaust air loav€s $e end of this unil, RIOUS INJURY. INCLUDING DEATH IN EX. cautionshould be obs€rvod not to positionunit TREMECASES. SAVE THESE INSTRUC. in sucfi a way as to block the oxhausl TtoNs. WARNING: (EXPLOSTONHAZARD) Tils unll contalns parts whlctr can arc or sparl( durinq normal op€ration. Do not uss In areas conta;nlnatedb'i votatile or flamible materials as th
9014 — SELECT SETTING switch with the following selections; OFF, 10A–12V AUTO, 2A–12V AUTO and 10A–6V MANUAL 9060 — SELECT SETTING switch with the following selections; 55A START, 10A–12V, 2A–12V and 10A–6V MANAUL — SELECT FUNCTION switch with following selections; CHARGE and START — Charge Complete Indicator light. — Reverse connection indicator light. 9070 — SELECT SETTING switch with the following selections; 70A START, 12A–12V, 2A–12V and 12A–6V — SELECT FUNCTION switch with following select
! Start the vehicle with the charger connected to the battery. NOTE: Do not crank the engine more than 20 seconds in any five minute period; excessive cranking may overheat and damage the starter. If the vehicle fails to start, while waiting for the starter to cool, allow the charger to continue to charge the battery. Unplug the charger before disconnecting dc clips from battery. POSSIBLE CHARGING PROBLEMS: 1. ! Meter needle swings to far right side of meter: (Manual). ! Reverse connection indic
The plug must be plugged into an outlet that is properly installed and grounded in accordance with all local codes and ordinances. DANGER. Never alter AC cord or plug provided - if it will not fit outlet, have proper outlet installed by a qualified electrician. Improper connection can result in a risk of an electric shock. This battery charger is for use on a nominal 120-volt circuit, and has a grounding plug that looks like the plug illustrated in FIGURE (A). A temporary adapter, which looks li
Insulated fiberglass backboard with 10 pairs DC charging leads, 10 gauge, 36” long with 300 Amp insulated safety clamps. Comes with three-foot 4 AWG cables to connect to charger or additional bus bars. Model 6086 Battery Charging Rack Battery charging rack stores up to 15 batteries. Convenient three-shelf, heavy-gauge steel construction rack with 10 pairs of charging leads. Insulated storage bars and connections ensure there are no live electrical connections. Shelves have durable 1/8” polypro