We reserve the right to make changes at any time without notice. Copyright© 2007 MTD SOUTHWEST INC, All Rights Reserved. WARNING: When using the unit, you must follow the safety rules. Please read these instructions before operating the unit in order to ensure the safety of the operator and any bystanders. Please keep these instructions for later use. P/N 769-02763 (1/07) WARNING THE ENGINE EXHAUST FROM THIS PRODUCT CONTAINS CHEMICALS KNOWN TO THE STATE OF CALIFORNIA TO CAUSE CANCER, BIRTH DEFEC
WARNING: Use extreme care when handling gasoline. Gasoline is extremely flammable and the vapors are explosive. Never fuel the machine indoors or while the engine is hot or running. Extinguish cigarettes, cigars, pipes and other sources of ignition. 1. 2. 1 2 3 Figure 3-6 Controls and Features 4 11 Blade Control The blade control is attached to the upper handle of the mower. Depress and squeeze it against the upper handle to operate the unit. Release it to stop engine and blade. WARNING: This bl
Less choking may be necessary due to variations in temperature, grade of fuel, etc. Little or no choking will be needed when the engine is warm. 3. Place the throttle in the "START" (1/2-3/4 throttle) position. Never start engine at full throttle. 4. Place the PTO switch to the "OFF" position. 5. Place the speed control lever in neutral ("N"). 6. Depress brake pedal all the way down. NOTE The speed control lever will automatically return to neutral when the brake pedal is pressed all the w
If a mower is mounted on the tractor, the mower must be lowered to facilitate removal of the filter. Remove the throw-away-can-type filter and replace with a new filter after the first 10 and 50 hours of operation, and every 100 hours of operation thereafter. The filters can be obtained through your Cub Cadet Dealer under part number 723-3014. To remove the filter, turn the filter counterclockwise using an automotive-type filter wrench. Before installing the new filter, apply a coating of oil
Adjust as follows: (See Figure 32.) 1. Loosen (do not remove) the hex bolt and nut at the stationary idler bracket. 2. Slide the idler pulley upward to tighten the belt. Tighten hex nut and bolt. When no adjustment is left, have belt replaced. 1. Idler Pulley 2. Hex Nut 3. Bolt 4. Drive Belt 21 DRIVE BELT REPLACEMENT If drive belt replacement is required, contact your authorized Cub Cadet Dealer. BATTERY INFORMATION A WARNING A. Battery acid must be handled with great care as conta
. . . . . . . . . . . . . . . .791-153066 Fuel Cap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .791-181612 Shoulder Harness . . . . . . . . . . . . . . . . . . . . . . . .791-682075B Tip-and-Pour 2-Cycle Oil (16 oz.) . . . . . . . . . . . . . .791-180965 These replacement parts can be purchased at the retailer from which you bought your trimmer, or your local Cub Cadet dealer. CLEANING To avoid serious personal injury, always turn your trimmer off and allow it to cool before yo
Read it carefully before assembly and operation of the equipment! CONGRATULATIONS on your the purchase pf your new Brinly-Hardy Lawn Sweeper! Your lawn sweeper is designed, engineered and manufactured to give you the best possible dependability and performance. CUSTOMER RESPONSIBILITIES Please read and retain this manual. The instructions enables you to assemble and maintain your lawn roller properly. And please, always observe the "Safety" instructions. TABLE OF CONTENTS SAFETY ............ ...
Remove the belt guard. 3. Remove the front PTO drive belt from the double drive pulley, and replace with a new belt. 4. Install the double drive pulley belt guard in the same position noted in step 1. Secure the belt guard in proper position using the washer and bolt. When the PTO drive belt has been replaced, the mower deck reinstalled onto the tractor, and the front PTO drive belt positioned onto the engine drive pulley and the idler pulley, refer to "DOUBLE DRIVE PULLEY BELT GUARD ADJUSTME
Use a 40:1 fuel/oil ratio. Do not mix them directly in the engine fuel tank. See the table below for specific gas and oil mixing ratios. NOTE: One gallon (3.8 liters) of unleaded gasoline mixed with one 3.2 oz. (95 ml) bottle of 2-cycle oil makes a 40:1 fuel/oil ratio. Gasoline is extremely flammable. Ignited Vapors may explode. Always stop the engine and allow it to cool before filling the fuel tank. Do not smoke while filling the tank. Keep sparks and open flames at a distance from the area. R
P.O. BOX 368023 CLEVELAND, OHIO 44136-9722 45” Snow Thrower Model 1345 SWE PRINTED IN U.S.A. Warning: This unit is equipped with an internal combustion engine and should not be used on or near any unimproved forestcovered, brush-covered or grass-covered land unless the engine’s exhaust system is equipped with a spark arrester meeting applicable local or state laws (if any). If a spark arrester is used, it should be maintained in effective working order by the operator. In the State of California