Gas leak. See Warning statement at 1. Locate and correct all leaks (see Check- position top of page ing Gas Connections, page 12) 2. Control valve defective 2. Replace control valve Gas odor during combustion 1. Foreign matter between control valve 1. Take apart gas tubing and remove for- and burner eign matter 2. Gas leak. See Warning statement at 2. Locate and correct all leaks (see Check- top of page ing Gas Connections, page 12) 18 OWNER’S MANUAL These Parts Centrals are privately owned busi

injury or property damage. Re m Do not store or use gasoline or other flammable fer to this manual for correct vapors and liquids in the vicinity of this or any other installation and operational pro- appliance. cedures. For assistance or addi- WHAT TO DO IF YOU SMELL GAS tional information consult a qualified installer, service agency, or • Do not try to light any appliance. the gas supplier. • Do not touch any electrical switch; do not use any phone in your building. WARNING: For use only with

These two holes are 14 inches apart from their centers. Attach mounting bracket to wall in one of two ways: 1. Attaching to wall stud 2. Attaching to wall anchor Attaching to Wall Stud: This method provides the strongest hold. Insert mounting screws through mounting bracket and into wall studs. Attaching to Wall Anchor: This method allows you to attach mounting bracket to hollow walls (wall areas between studs) or to solid walls (concrete or masonry). Decide which method better suits your needs.

3 -4 specifications .............................................................................................................. 5 product features ..................................................................................................... 5 unpacking and assembly ............................................................................................ 6 propane supply ........................................................................................................... 7 con

Vent-free heater _________________ Btu/Hr Gas water heater* _________________ Btu/Hr Gas furnace _________________ Btu/Hr Vented gas heater _________________ Btu/Hr Gas fireplace logs _________________ Btu/Hr Other gas appliances* + _________________ Btu/Hr Total = _________________ Btu/Hr Example: Gas water heater 40,000 Btu/Hr Vent-free heater + 20,000 Btu/Hr Total = 60,000 Btu/Hr * Do not include direct-vent gas appliances. Direct-vent draws combustion air from the outdoors and vents to the o

The mounting clip must be a minimum of 3" Capillary from bottom of fireplace to prevent crimping Do Not Crimp of capillary. Once you have decided on a Capillary location, clean the area thoroughly. Remove Figure 44 - Positioning the Thermostat the paper backing from the adhesive on back Sensing Bulb in the Vertical Position of mounting clip. Press the clip into the new with the Capillary at the Bottom location so that the thermostat sensing bulb will be positioned vertically with the capillary a

Exhaust fans, fireplaces, clothes dryers, and fuel-burning appliances draw air from the house to operate. This heater is a fuel-burning appliance. It uses air from inside the house for combustion. It also uses this air as a draft for venting. This draft air helps move combustion gases through the vent pipe to the outdoors. If your house is too airtight, there is not enough fresh air for these items to use. Fresh air may draw back into the house through venting flues and chimneys. This will keep

3. You prefer vented operation. If reasons number 1 or 2 above apply to you, you must permanently open chimney flue damper. You must install the damper clamp accessory (to order, see Accessories, page 33). This will insure vented operation (see Figure 10). The damper clamp will keep damper open. Installation instructions are included with clamp accessory. See chart below for minimum permanent flue opening you must provide. Attach damper clamp so the minimum permanent flue opening will be maintai

WARNING: Improper installation, adjustment, alteration, service, or maintenance can cause injury or property damage. Refer to this manual for correct installation and operational procedures. For assistance or additional information consult a qualified installer, service agency, or the gas supplier. FOR YOUR SAFETY Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance. FOR YOUR SAFETY WHAT TO DO IF YOU SMELL GAS • Do not try to light any

If installing bottom mounting screw into wall stud, drill hole at marked location using 9/64" drill bit. 5. Replace heater on wall. 6. Insert bottom anchor screw through back panel into bottom anchor or drilled hole (see Figure 11). 7. Tighten screw until heater is firmly secured to wall. Do not over tighten. Note:Do not replace front panel at this time. Replace front panel after making gas connections and checking for leaks (see pages 13-15). Figure 11 - Installing Bottom Mounting Screw CONNECT