Capacitor Connections The starting winding of a motor can be damaged by a shorted and grounded running capacitor. This damage usually can be avoided by proper connection of the running capacitor terminals. From the supply line on a typical 230 volt circuit, a 115 volt potential exists from the “R” terminal to ground through a possible short in the capacitor. However, from the “S” or start terminal, a much higher potential, possibly as high as 400 volts, exists because of the counter EMF generate

• Make sure to protect personal and surrounding property with fire proof materials. • Have a fire extinguisher at hand while using a torch. • Provide adequate ventilation to vent off toxic fumes, and work with a qualified assistant whenever possible. • Always use a pressure regulator when using dry nitrogen to test the sealed refrigeration system for leaks, flushing etc. • Make sure to follow all safety precautions and to use proper protective safety aids such as: gloves, safety glasses, clothin

3. Flush evaporator condenser and all connecting tubing with dry nitrogen or equivalent, to remove all contamination from system. Inspect suction and discharge line for carbon deposits. Remove and clean if necessary. 4. Reassemble the system, including new drier strainer and capillary tube. 5. Proceed with processing as outlined under hermetic component replacement. ROTARY COMPRESSOR SPECIAL TROUBLESHOOTING AND SERVICE Basically, troubleshooting and servicing rotary compressors is the same as on

To register your dehumidifier, complete and mail the enclosed registration card, or register on-line at (USA only). For your future convenience, record the model information here. MODEL NUMBER SERIALNUMBER PURCHASEDATE 920-154-00 (12/04) Safety Precautions ......................................3 Installation ................................................. 13 Prior to Operation .......................................7 Maintenance and Service ......................... 14 Instruction ............

DISASSEMBLY INSTRUCTIONS 2.1 MECHANICAL PARTS....................................5 2.1.1 FRONT GRILLE.....................................5 2.1.2 CABINET................................................5 2.1.3 CONTROL BOX.....................................5 2.2 AIR HANDLING PARTS..................................6 2.2.1 ORIFICE, HEATER ASSY AND TURBO FAN .........6 2.2.2 FAN........................................................6 2.2.3 SHROUD................................................7 2.

Indoor air is not rejected (wasted) and vented outside. The room is cooled up to 40% faster with greater energy efficiency. SINGLE HOSE DESIGN BOTH INDOOR AIR AND REMOVED HEAT ARE EXHAUSTED Single hose design relies on air ‘leakage' from doors and windows to make up for air volume lost as indoor air is exhausted outside. The room takes longer to cool using more energy. Ideal for these applications • Workshops and garages • Bedrooms, attics and basements • Home offices • Sunrooms/ enclosed

In case of questions regarding the provisions of this warranty, the English version will govern. Revised (10/00) 19 Memo 20 Guide d’installation & de fonctionnement Series murales 115 Volts UE08 US08 US10 US12 230 Volts US10 UE10 US12 UE12 NUMERO DU MODELE NUMERO DE SERIE DATE D’ACHAT Les informations sur le modele sont sur la plaque avant de l’unite. Pour enregistrer votre application, remplir et envoyez la carte d’enregistrement jointe par courrier ou enregistrez-vous en ligne a (US seulement.

12 18 D 18-5/83/4 18-5/8 D 19-3/41-3/4 19-3/4 D 22 4 Place the plastic grille FIG. 9 3 Fasten the 4 washer screws to secure the grille to the wall sleeve. If you need plastic nuts to mount plastic grille to the inside of the wall sleeve, there are plastic nuts in the installation kit. The nuts are installed from the inside of the sleeve and are pressed into the square holes of the rear flanges. or Fasten the screws FIG. 10 6 Remove the backing from the support blocks and attach them to the insid

2.36”) • Height limit: below 25ft. • Maximum tubing length: below 50ft. Tubing length over 25ft. 9/12 Btuh (Single or Multi-Zone) • Charge additional refrigerant amount, additional refrigerant amount =0.44oz./ft.>25’. • Capacity drops slightly. More than 12” More than 2” More than 16” More than 4” More than 10” INSTALLATION (Single Zone Shown) NOTE: Always check superheat and subcooling of system. (22.72”) 9/12 Btuh (23.94”) 18/24 Btuh (8.86”) 9 Btuh( 11.02”) 12 Btuh(14.25”) 18/24 Btuh Distance

9 Disassembly ..................................................................................................................................................10 Mechanical Parts..................................................................................................................................... 10 Air H andling Parts ...................................................................................................................................11 Electrical Parts .............