MESSAGE CENTER TO: PRESS: Record a message: # + 1 Stop recording before end of 20 seconds: 1 Playback a message: # + 3 Adjust message playback volume: # + 2 + 39 or 6. Mute keypad status announcements: # + 2 + 1 Restore keypad status announcements: # + 2 + 39 or 6. New message indication: If powered by battery, the Message LED will only blink when you activate the keypad by requesting status. If powered by AC, the Message LED will blink continuously. Once the message is played back, the LED will

Instruction Manual RCWL300A Premium Portable Wireless Chime & Push 69-2109EFS-05 Installation Instructions 69-2109EFS—05 ii Contents Checking pack contents.............................1 Safety...........................................................2 Quick start...................................................2 Open bell push............................................3 Fit the push battery....................................3 Fit the chime battery...................................4 Sliding

This device operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Caution: Changes or modifications not expressly approved by the party responsible for regulatory compliance could void the user’s authority to operate the equipment. Honeywell International Inc. ACS, Environmental and Combustion Controls 1985 Douglas Drive, Golden

This thermostat has been tested and found to comply with the requirements of the European Union for Electromagnetic Interference, Electromagnetic Immunity and Safety under the applicable EMI and Low Voltage Directives and Standards. FCC This thermostat has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. This product generates and can radiate radio frequency energy. Due to its low power design, it is unlikely to interfere with ra

The air going to the unit and the discharged air may be transported by a network of ducting and plenums or the unit can be used independently. The Honeywell Trademark is used under license from Honeywell Intellectual Properties, Inc. by Air-Pure Systems. Honeywell International Inc. makes no representations or warranties with respect to this product PRODUCT DATA FEATURES • Variety of filter configurations available to customize the air cleaner for any application. • Three-speed direct drive forw

The L404F should always be mounted above the water line in steam boiler applications. NOTE: For accurate operation, supplemental heat should be added to installations where temperatures fall below -29°C (-20°F). A steam trap must be connected between the L404F and the boiler (see Fig. 2) to prevent boiler scale and corrosive vapors from attacking the elbows or diaphragm. PRESSURE GAUGE 4-1/2 TO 5-1/2 (114.3 TO 139.7) BOILER STEAM TRAP (SIPHON LOOP) TEE PRESSURE CONTROLLER 1 1 1/4 IN. PIPE WITH 1

The options for this menu item are: • “SIGNAL > SETPOINT” means the limit will activate when the signal is higher than the set point. • “SIGNAL < SETPOINT” means the limit will activate when the signal is lower than the set point. • “SIGNAL INSIDE” means the limit will activate when the signal is in between the set point and the return point. • “SIGNAL OUTSIDE” means the limit will activate when the signal is not in between the set point and the return point. The figures below further illustrate

Please visit our website at CLEANING AND STORAGE We recommend that the heater be cleaned at least once a month and before off-season storage. • Turn the heater OFF and unplug it. Allow it to cool. • Use a dry cloth only to clean the external surfaces of the heater. DO NOT USE WATER, WAX, POLISH OR ANY CHEMICAL SOLUTION. • Clean your heater using the above-mentioned steps, then pack the heater in its original container and store it in a cool dry place. • This heater does not disassemble. ELECTRIC

If you are using an RS-232 cable, ActiveSync will usually set up an RS-232 connection. For more details, see ActiveSync Communication on page 7-8. Connecting the Cables Connect the base to the host workstation or other device by plugging an RS-232 serial cable into the RS-232 Communications Port on the bottom of the base. Plug the other end of the RS-232 serial cable into the correct port on the host RS-232 device. The wiring of your cable depends on whether the other device is set up as a D

HD-16DVR-C Digital Video Recorder User Manual Contents 1 Features and Specifications................................................................................................1 Overview......................................................................................................................1 Features......................................................................................................................1 Specification................................................