Dimensions in parentheses are in millimeters unless otherwise specified. 2 Planning Information Planning Information Pro Island Ventilation Hood MODEL PI663418(R) BLOWER OPTIONS SPECIFICATIONS 1200 CFM Internal Blower as of Fall 2007 1100 CFM In-Line Blower 1200 CFM Remote Blower 804703 810317 808332 801642 Overall Width of Hood Overall Height of Hood Overall Depth of Hood (including rails) 66" (1372) 18" (457) 34" (864) 38" (965) 1500 CFM Remote Blower 804701 Internal Blower Option 1200 CFM Ref
Optional platinum or brass rails match dual fuel range bezels. Pro wall hoods are sold as a shell only; internal, in-line and remote blower options are available. Hand finished Classic stainless craftsmanship steel finish Stainless steel baffle filters Location of rating plate Infinite-speed Welded seams and hemmed edges Recessed easy- access controls Decorative rail (optional) Halogen lighting blower control Model PW362718R shown with decorative rail. Wolf Pro wall hoods provide the ultimate in
Optional platinum or brass rails match dual fuel range bezels. Pro wall hoods are sold as a shell only; internal, in-line and remote blower options are available. Hand finished Classic stainless craftsmanship steel finish Stainless steel baffle filters Location of rating plate Infinite-speed Welded seams and hemmed edges Halogen lighting Recessed easy- access controls Decorative rail (optional) blower control Model PW662418R shown with decorative rail. Wolf Pro wall hoods provide the ultimate in
A 10" (254) round duct is recommended for pro ventilation hood liners. Use only rigid metal ductwork, do not use flex ducting. Decide where the ductwork will run between the hood liner and the outside. Pro hood liners have a vertical discharge. A straight, short duct run will allow the ventilation hood to perform most efficiently. Limit the number of elbows and transitions. The duct run should be no longer than 50' (15 m). There is a possibility of noise issues, if a remote blower is used with a
Discharge Vertical ACCESSORIES Duct Size 10" (254) Round 38" (965) high classic stainless steel backsplash with or without Electrical Supply Requirements 110/120 V AC, 60 Hz 15 amp dedicated circuit warming racks Shipping Weight (shell only) 68 lbs (31 kg) Specifications are subject to change without notice. Wolf dealer. To obtain local dealer information, visit the Showroom Locator sectionofourwebsite,wolfappliance.com. Accessories are available through your Dimensions in parentheses are in mil
You must follow all National Electrical Code regulations. In addition, be aware of local codes and ordinances when installing your service. A decorative hood can be created out of wood, plaster, tile or metal. The shape of the decorative hood is not critical. The only place where the liner and outside cover must meet is at the bottom edge of the metal liner. The decorative hood and liner must fit at the bottom edge in both width and depth. The height of the liner does not have to be the same as
Optional platinum or brass rails match dual fuel range bezels. Pro wall hoods are sold as a shell only; internal, in-line and remote blower options are available. Hand finished Classic stainless craftsmanship steel finish Stainless steel baffle filters Location of rating plate Infinite-speed Welded seams and hemmed edges Recessed easy- access controls Decorative rail (optional) Halogen lighting blower control Model PW482418R shown with decorative rail. Wolf Pro wall hoods provide the ultimate in
See warranty details at the end of this guide. WOLF PRO VENTILATION HOOD USE & CARE RECESSED CONTROLS Controls for Pro ventilation hoods and hood liners are recessed under the front edge of the hood. Refer to the illustration below. LIGHT CONTROL The left rotary switch operates the halogen lights. There are two settings, HIGH and LOW. The LOW setting can be used as a night-light. From the OFF position, turn the switch to the desired light setting, left for LOW and right for HIGH light setting. H
Rail option hoods (R) come with a classic stainless steel decorative rail and stand-offs. Optional platinum or brass rails match dual fuel range bezels. Pro wall hoods are sold as a shell only; internal, in-line and remote blower options are available. Hand finished Classic stainless craftsmanship steel finish Stainless steel baffle filters Location of rating plate Infinite-speed Welded seams and hemmed edges Recessed easy- access controls Decorative rail (optional) Halogen lighting blower contr
Verify that the screws engage the wall framing. If not, wall anchors must be used. If additional support is required for the wall hood, drill supplementary mounting holes in the back plate and use these holes to attach the hood assembly to the wall framing. WIDTH OF HOOD WIDTH OF HOOD 261/4" (667) TO MOUNTING BRACKET HOLE CENTERS 131/8" (333) HOOD CENTERLINE USE ROUND AND SLOTTED HOLES TO SECURE HOOD TO WALL STUDS MOUNT BRACKETS TO WALL FRAMING 77/16" (189) TO TOP OF BRACKET Low-profilewallhoods