Box 80400 Simpsonville, S.C. 29680-0400 Or call toll free: 1-800-927-6887 Outside the U.S., call 864-963-3471 Protect Children Keep children away from this equipment. Children may not understand that this equipment is dangerous for them and others. NEVER allow children to play near or operate your equipment. Keep Safety Labels Clean and in Good Condition Do not remove or cover any safety labels on your equipment. Keep all safety labels clean and in good condition. Replace any damaged or missing

4 Installation................................................................................................................................................................ 6 Instructions For Shipping Damage........................................................................................................................ 6 Electrical Information............................................................................................................................................. 6 Im

Remove those nuts and washers to free the wires. (Fig. 48) 4. Remove air deflector housing" and place on a clean work area. 5. Remove four screws securing the heating element brackets to the ceramic insulators with a medium (6") flathead screwdriver. (Fig. 49) 6. Slide brackets off the old element and discard the old element. 7. Slide brackets (large one first) over the connector end of the new heating element. (Fig. 50) 8. Reconnect heating element brackets to the ceramic insulators with the fo

Use of oil/shortening older than the manufacturers recommendations for life of the oil is prone to surge boiling and flash fires. Follow the oil manufacturers guidelines for the life cycle of oil/shortening. Do not open the drain valve or the fill valve while the fryer is under pressure. Serious burns may result. Follow operator instructions regarding effects of surge boiling of over-wet foods and proper load size. This unit may incorporate components that contain Mercury. The use of Mercury rel

Allow the equipment to preheat for 30 minutes before loading it with product. Unit Shutdown 1. Place the Sandwich Warmer POWER ON/OFF switch to the OFF (0) position. 2. Unplug each power cord from it’s receptacle. 3. Allow the equipment to cool to room temperature. 10 Sandwich Merchandiser Operation Temperature Adjustment After loading the unit with product, it may be necessary to adjust the temperature control knobs in order to maintain the proper internal temperature for the product on display

FOOD CONTAINERS “Hot Shop” food display cabinets are supplied with a mezzanine shelf and 65mm deep 1/1 gastronorm pans fitted with wire inserts as standard. Wet Foods :- Chicken, cooked meats etc, should be placed in the gastonorm pans, on the wire inserts to allow for drainage. Pies, Pastries :- Should be placed above on the mezzanine shelf. The gastronorm pan section can be split up using the various sizes available in the gastronorm pan range, to a maximum depth of 65mm see page 11 (spare par

Read the installation, operating and maintenance instructions thoroughly before installing or servicing this equipment. This equipment has been engineered to provide you with year round dependable service when used according to the instructions in this manual and standard commercial kitchen practices. Instructions must be posted in a prominent location. All safety precautions must be taken in the event the user smells gas. Safety information can be obtained from your local gas supplier. DESIGN C

Dead Weight Assembly Table 3. Dead Weight Assembly Parts ITEM # PART # QTY DESCRIPTION 1 FT0395 1 PIPE, POPOFF VALVE BAFF BOX 2 FT0396 1 PIPE, DEAD WT TO BAFFLE BOX 3 O0001 1 ORIFICE, SS 4 O0002 1 GASKET, O-RING #2-222 5 PV0001 1 VALVE, POP SAFETY 1321148 6 FT0066 1 ELL, REDUCER 3/4 X 1/2 90 DEG 7 FT0235 1 NIPPLE, 1/2 X C SS 8 FT0190 1 ELL, STREET 1/4 90 DEG CP 9 FT0084 1 COUPLING, BRASS 1/4 10 FT0563 1 FITTING, COMPRESSION .” 11 FT0067 1 BUSHING, C110JO 3/4 X 1/2 CP 12 FT0234 1 NIPPLE, 1/4 X 1

Remove thermostat dial from front panel by rotating the dial to expose the set screw and reversing the sat screw with a small flathead screwdriver. (Fig. 34) 4. Remove the two screws holding the bezel (chrome ring) behind the thermostat dial with a medium (6”) phillips screwdriver. Carefully pull thermostat away from the rear of the front cover. 5. Remove the fan blower motor assembly cover (on the left side of module as you are facing the front panel) by removing the two front and two rear scre