The casting top nests into the casting. 18. Insert center grill, left grill and right grill into casting top. 19. Level appliance by adjusting leveling bolts. 20. Assembly of stove casting is completed. OPTIONAL STONE INLAY INSTALLATION Whenever the standard grill top is replaced with a stone inlay you must install the top shield and heat shield, which are provided with the stone inlay. Installation of Optional Stone Inlay 1. Remove left grill, center grill and right grill from casting top. 2. R

The Com-Pak™ Plus 111/2” 29.21 31/4” 8.26 11/4” 3.18 10” 25.4 13/4” 4.45 11/4” 3.18 77/8” 20.00 4” 10.16 3” 7.62 9” 22.86 12” 30.48 10” 25.4 111/8” 28.26 12” 30.48 161/4” 41.27 The Com-PakTM Plus Model C The Com-PakTM Twin Plus Model CT Side Wall Can Side Grill Front Wall Can Bottom Side Wall Can Side Grill Front 3” 7.62 141/2” 36.83 4” 10.16 Wall Can Bottom TOOLS REQUIRED: Phillips Screwdriver Straight ScrewdriverWire Strippers Utility Knife 411/2“ Wood Screws 3 Insulated Wire Connectors 1 Stra

WARNING! Risk of Fire. Heaters must be kept clean of lint, dirt and debris. Failure to follow warnings may cause heater to eject sparks, ignite materials, or cause electrical shock. Horizontal Delivery Heaters should be located so that the air streams of the individual units “wipe” the exposed walls of the building without blowing directly against the wall. Recommended spacing between the units is 12 feet. Locate heaters so their air streams are not subjected to interference from columns, partit

2. DO NOT operate the heater unless it is level and the mounting feet and front cover are in place. 3. Do not place heater against paperboard or low-density fiberboard surfaces. 4. Do not place heater below or above an electrical convenience receptacle. 5. The chemical properties of some synthetic fibers used in draperies and furniture may cause fading when exposed to any heat, even at low temperatures. Maintain a 12-inch minimum clearance in front and above the heater with a 6-inch minimum on e

When using electrical appliances, basic precautions should always be followed to reduce the risk of fire, electric shock, and injury to persons, including the following: Tel: 360-693-2505 P.O. Box 1675 Vancouver, WA 98668-1675 9. WARNING Risk of electrical shock. Connect to properly grounded outlets only. Do not insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause an electric shock or fire, or damage the heater. Unplug heater before performing any mainten

2. Replace element or heater. Heater not working 1. Heater does not have proper voltage to function correctly 2. Unit wired incorrectly 1. Circuit breaker could be positioned incorrectly. Relocate breaker. Check voltage at the heater between supply wires and make sure it matches required heater voltage. 2. Using Owner’s Guide, verify wires are connected properly and securely with appropriate wire nuts. If the unit is still not operating, further testing should be done with ohmmeter. Consult an e

Replacement Loose Material (glowing embers) Part Number LS-18P 15999 LS-24P 15970 LS-30P 15970 Platinum Bright Embers PE-20-1 Note: A single layer of embers is to be used when applying Platinum Bright Embers (alone or in combination with production embers) to the burner. Log Placement LS-(18, 24, 30)P Logs Figure 5 Attention: Do not use Figures 1 to 5 to order replacement logs. Refer to Page 11, Parts List and Parts View to order logs for your appropriate model number. The following WARNING appl

9. Depress and turn gas control knob counterclockwise to “PILOT”. A spark is produced when gas control knob is turned between “IGN” and “PILOT”. Repeatedly depress and turn gas control knob between “IGN” and “PILOT” until pilot is ignited. Continue to hold the control knob in for about one (1) minute after pilot is lit. Release knob and it will pop back up. If it goes out, repeat steps 5 through 9. • If knob does not pop up when released, stop and immediately call your service technician or gas

Failure to do so could result in serious electrical shock, burns, or possible death. CAUTION - High Temperature. Keep electrical cords, drapes, and other furnishings away from heater. When using electrical appliances, basic precautions should always be followed to reduce the risk of fire, electric shock, and injury to persons, including the following: 1. Read all instructions before using this heater. 2. Read all information labels. Verify that the electrical supply wires are the same voltage as

If replacing an existing heater check the labels of the old heater and replace using same voltage. Hooking a 240 volt heater to a 120 volt power supply will drastically reduce the heater’s output. Hooking a 120 volt heater to a 240 volt power supply will destroy the heater. WATTAGE (FOR MODEL 8F2025) Model 8F2025 is a multi-watt unit configured for either 2500 or 2000 watts. The heater is factory set for 2500 watts, but the instructions vary depending on your desired wattage and which side you a